79641962610 Kenmore Washer - Instructions

Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!

Use just your finger to push it into place. VERY EASY

Turned off hot and cold water supply. Pulled out machine and disconnected hoses, unplugged power.

Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.

Slid cover back and up. This was the only tricky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.

Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.

Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.

Replace cover. Screw all screws back to secure cover. Replace trays.

The repairs went great thanks to the videos and Steve.

First unplug the machine. Turn the water off to the hoses. Remove the hoses from the machine to make it easier. Remove the screws from the back of the top cover. Pry the front sides with a screwdriver and lift. Standing behind the machine on the left side you’ll see the three solenoids or inlet assembly. Remove the two screws so as to take the inlet assembly out. There are hoses attached to the assembly.

Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.

Do not start this project without the required spring expansion tool for the retaining ring springs.
Nearly impossible without it.

Took front of machine off to access 2 shocks, put back together then removed panel in back to access third shock, watched YouTube video first so things went smooth

Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.

you tube it , not to hard to install

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

YouTube is your friend for many such repairs. See this link for an overall description:

https://www.youtube.com/watch?v=WuvLuC8x4_s

I had to remove the top panel to determine exactly which valve was leaking. It turned out both hot and cold-water valves were defective.

After unit is unplugged and top is removed, it's a simple matter to remove/replace hose connections and electrical connections. It took me less than an hour to complete the task once parts were in hand.

Again, YouTube is your friend for such repairs.

Unplug and disconnect water lines. Move washer out. I used soapy water to make it easier to slide because it is stacked washer and dryer. Slid dryer onto large trash can saving my back. So easy. Make sure it is heavy duty . Removed lid. Removed old part by removing to screws in back. Disconnected 3 wires, disconnected one hose at a time while reattaching each one to new part. That way I was sure to get them back in the right place. Attached back to machine . Put water hoses back on and checked for leaks before but lid and dryer back in place. Ta da!! This was so easy. I am a 57 year old woman and this was pretty simple. I tried trouble shooting by using tub cleaner and everything as manual suggested but it still leaked. Watch a lot of you tube. Apparently lg has this happen with this part a lot. Thank you parts select. I’m sure this saved me a lot of money. I have had enough money bleeding from my pockets with bigger home problems. Thank you.

pops right into hole

I actually did the repair exactly as the video showed. If I would have had the part at the time of discovering the problem it would have been about a 45 minute repair from start to finish. Worst part of the whole fix was moving the heavy washer.