All Installation Instructions for Kenmore Range 79092321300

Oven door inner glass cracked after cleaning

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

Parts Used:

GLASS

Lisa from Erial, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The elements were not heating up

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Parts Used:

Main Terminal Block Kit

Tanya from KALISPELL, MT
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

old element coil burned apart breaking the circuit.

removed the old burner and put the new one in it's place.

Parts Used:

Radiant Element with Limiter - 1200W

James from WARRENTON, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Glides broke on lower storage drawer

The front glides easily snap into a hole on the sides of the range. The rear glides easily snap onto the sides of the lower rear of the drawer.

Parts Used:

Rear Drawer Glide

Front Drawer Glide

James from WEST BEND, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Lenses wore down and broke off making the actual indicator lights fall down behind the control panel since the lights connect to the lens.

Pulled stove out and unplugged it.
Used a Phillips screwdriver to take the back cover off of the control panel.
Each of the 7 lights connects to the red Indicator Light Lens via a slide clamp which is attached to the front of the light assembly. All you have to do is slide the lens into the hole from the outside of the control panel. Then with your other hand, pust the light assembly into the back of the lens and slide it to lock it in place. Repeat with the others.
Replace back cover.
Plug stove back in and slide back into place.
There are you tube videos out there to help you.

Parts Used:

Indicator Light Lens

Charles from OMAHA, NE
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

While removing burned out light bulb, the glass cover fell to the floor of the oven and broke!!

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Parts Used:

LENS

Phyllis from GAINESVILLE, GA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The glass on the enter oven door was broken

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

Parts Used:

GLASS

leslie from Pickerington, OH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

replacing oven racks

The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

Parts Used:

Oven Rack

Lawrence from Elmira, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Old racks had melted plastic on them.

It was a replace racks not repair. No problem

Parts Used:

Oven Rack

James from PAINESVILLE, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Broken door glide

snapped the new piece of plastic in its place and ta da, its fixed.

Parts Used:

Rear Drawer Glide

Front Drawer Glide

Michael from Signal Hill, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Repaired Oven Range Light Bulb

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Parts Used:

Light Bulb

Alan from SAN MATEO, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Drawer Glide Was Broken

Took the drawer out, snapped the new glide in place, and replaced the drawer. Installation was simple with no tools required.

Parts Used:

Front Drawer Glide

Karen from Yuma, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Never received parts from PartSelect!!!

It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!

Parts Used:

PROBE

Ralph from SULLIGENT, AL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven wires arced and caused the terminal block to melt and become detached from the back of the range

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

Parts Used:

Main Terminal Block Kit

Daniel from Falmouth, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The surface element quit working, when I tried to remove it, the element cracked.

Turn power off to the stove! Opened the oven door, removed 3 screws holding the top down. Lift the top up. (Take a picture first of where exactly the wires go and where the prongs go) I unplugged the 4 wires from the element. Use a screwdriver and pry the prongs through the metal brace. Remove the prongs from the old element because they are a separate part and don't come with a new element. If you wish to continue to use the stove, tape the ends of the wires up, because they will be hot when you turn any other burner on.

Parts Used: