Models > 75199 > Instructions

75199 LG Refrigerator - Instructions

All Instructions for the 75199
31 - 45 of 68
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer door gasket needed replacing.
Simply removed old gasket. Started in a corner with installing the new gasket. It went in easily and quickly.
Parts Used:
GASKET,DOOR
  • Stephen from DICKINSON, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door switch would not turn on interior refrigerator light.
I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.
Parts Used:
Refrigerator Door Switch
  • Jane from SHORELINE, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light didn't come on when the door was opened
I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.
Parts Used:
Refrigerator Door Switch
  • William L from SUMAS, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch stops working
Replace with new switch. this is the third switch i have replaced in 10 years. the only part, besides a light bulb, that has gone bad. obviously this is a problem with this model for Kenmore, or just poor switch design.
Parts Used:
Refrigerator Door Switch
  • David from PENNSVILLE, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light quit coming on when door opened.
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.
Parts Used:
Refrigerator Door Switch
  • Calvin from Northome, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The switch became intermittent - Possibly a poor designe
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.
Parts Used:
Refrigerator Door Switch
  • Sidney from ENDICOTT, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Interior light switch not working
Remove two screws on top of the fridge; removed old switch and inserted new switch. Worked like a charm. Replace casing and screws.
Parts Used:
Switch,Push Button
  • Sharon from HOULTON, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door light switch, 3rd one I have replaced in 6 years made in China.
Easy install, small screwdriver under back of old switch push out and pull out with small pliers. unsnap the old plug and install new. YOUR DONE
Parts Used:
Refrigerator Door Switch
  • Charles from CURWENSVILLE, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace switch
Read previous tips
Taped off area around switch to protect surface
Used putty knife to extract switch
Used screwdriver to separate connector from switch
Plugged in connector
Pushed switch assembly into opening
Removed tape
Parts Used:
Refrigerator Door Switch
  • Dean from HILLSDALE, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water/ice maker not working
Remove push plate for water/ice maker switch, remove 2 screws and 2 wires for switch. Replace with new.
Parts Used:
Switch,Micro
  • Brent from ROGERS, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
6 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the light did not work when door was opened. At first it would flicker then off completely.
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)
Parts Used:
Refrigerator Door Switch
  • Alma from Winterport, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Parts Used:
Refrigerator Door Switch
  • Karyn from DURHAM, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old gasket was damaged
i removed old and installed new gasket in 5 minutes. i watched a video. it was super easy .
Parts Used:
GASKET,DOOR
  • Maria from TEQUESTA, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left door when opened the light wouldn’t come on. Checked the light, ok. Ordered push button switch
Removed the cover 2 screws
Squeezed the 2 side sleeves and removed
Snapped in new button, replaced the cover. Done
Parts Used:
Push Button Switch
  • Richard from TULLY, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice buildup in corner of freezer.
Reviewed instructions on YouTube. Removed storage box.Removed Philips head screw on either side of track. Lifted door and placed it on table. Using a flat blade screwdriver removed old gasket (it did not looked damaged). Pressed new gasket into groove in door. Replaced door onto track and replaced screws. Replaced storage box. No more ice buildup.
Parts Used:
GASKET,DOOR
  • Louis from BOYNTON BEACH, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 75199
31 - 45 of 68
Back to Top