All Installation Instructions for Kenmore Dishwasher 66517152K216

Stripped the fill valve when installing

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

Parts Used:

Dishwasher INLET VALVE

Jerry from Groton, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Dishwasher was not drying the dishes.

I followed installation instructions from this site and all went well.

Parts Used:

Dishwasher Heating Element

Mike from BOULDER, CO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

1 person found this instruction helpful.

Was this instruction helpful to you?

Heater element snapped in two.

Disconnected power,water supply and drain.Had to pull dishwasher out to access the heater element nuts. Removed broken element and replaced with new part. Repair very easy!

Parts Used:

Dishwasher Heating Element

Steve from The Colony, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

bad heater in qiuet partner 2

this job is cake. worst part is removing dishwasher from cabinet. Disconnect water , drain , and power. reove mounting screws in upper door area. Pull unit out and lay it on its face. unplug two wire leads and remove big nuts. Roll unit upright and replace heater. roll unit back over and tighten nuts and plug leads back in. It really takes two minutes to replace heater once the unit is out of cabinet.

Parts Used:

Dishwasher Heating Element

Rich from hamilton, MI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Stop broke

Looked at how the other was installed oh and bought 2 for when the other one fails. Great customer service!!!!

Parts Used:

Dishwasher Rack Track Stop

Melissa from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

snap

Just snap it in

Parts Used:

Dishwasher Rack Track Stop

William from MCMURRAY, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dishwasher was leaking a lot, 1-2 cups of water

Changed the seal first, very easy, no tools needed either. Helped a little, but still leaking a lot. Changed the lower spray arm and that did it. The video I watched before changing the seal helped a lot, definitely do that first.

Parts Used:

Dishwasher Lower Spray Arm

Douglas from BELFORD, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

DISHWASHER WOULD NOT FILL WITH WATER

Unscrewed bottom panel of the dishwasher and simply replaced the bad control switch with the new one.

Parts Used:

Dishwasher Overfill Control Switch

TRACEY ANN from BRICK, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

My dishwasher quietpartner ii was not cleaning my dishes. It seemed it was not heating correctly that the Hi temp wash or the heated dry.

I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!

Parts Used:

Dishwasher Heating Element

Dishwasher High Limit Thermostat

Jesus from Tucson, AZ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

1 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Clean light was flashing and washer would not start

Replaced heating element and high limit thermostat. Was suppose to fix the problem but did not. Replaced the control board and works now. All of these are easy to replace.

Parts Used:

Dishwasher High Limit Thermostat

Raymond from Beach, ND
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

hose had a hole and leaked

I pulled the dishwasher out from the countertop rolled it to the side removed old clamps and hose installed new hose in kind used different hose clamps than provided turned up right pushed back in ran a cycle while looking underneath with a flashlight and saw no leaks and dishwasher has been back in use for a week now.Chris

Parts Used:

Dishwasher Hose

Christopher from Delaware City, DE
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Both outside door handles turned very beige

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Parts Used:

Spray Paint - 12 oz. - White

Howard from Boynton Beach, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

23 of 72 people found this instruction helpful.

Was this instruction helpful to you?

black scratchers from wheel chair

shook bottle and painted waited a day and repeated

Parts Used:

Touch-up Paint - Black

Touch-Up Paint - Biscuit

Linda from GLEN CARBON, IL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins

3 of 12 people found this instruction helpful.

Was this instruction helpful to you?

just wanted to replace the upper dish rack - the pieces have been rusting through

no instructions came unfortunately, but it wasn't too difficult reverse engineering. took the upper rack out, disassembled it and put the new rack together using the old screws (since there were no screws either with the replacement rack). There are some extra parts I don't know quite what to do with - some type of additional separators, but the rack works fine without them.

Parts Used: