66516632000 Kenmore Dishwasher - Instructions

I ORDERED THE PART THAT WAS EASY BUT WHILE THE MACHINE WAS USED FOR HOW LONG I DON'T KNOW WITH OUT THE CAP IT GOT FILLED WITH FOOD AND JUNK. FIRST THING I HAD TO DO WAS EXAMIN THE DOOR AS TO HOW I COULD CLEAN THIS THING OUT. I REMOVED 6 SCREWS THAT HELD THE DOOR TOGETHER AND PULLED EASY CAUSE I DIDN'T KNOW WHAT I WAS GETTING INTO. NO PROBLEM THERE WAS NO ELECTRIC PLUGS HOOKED TO THE DOOR. I TOOK IT OUT SIDE AND STARTED USING VINIGAR AND POURING IT INTO THE HOLE AND SHAKING THEN TRYING TO GET IT BACK OUT. WELL THERE IS ONLY ONE POSITION THAT WILL LET THE VINEGAR BACK OUT. I HAD TO HOLD IT SIDEWAYS THEN TILT FORWARD AND IT WOULD RUN OUT AND BRING SOME JUNK WITH IT. THIS WAS A TIME CONSUMING PROCESS BEING YOU COULD NOT SEE INSIDE TO KNOW HOW MUCH JUNK WAS IN THERE. JUST POUR AND DUMP. AND DON'T FOR GET TO SHAKE TO LOOSEN ANY THING LEFT INSIDE.LOL I WAS VERY PROUD OF MYSELF NOT KNOWING FOR SURE IF I FIXED IT OR NOT BUT I TOOK A SHOT I HAD. I DID SOME SCRUBBING AND DEGREASING ON THE UNDERSIDE OF THE BOTTOM OF THE DOOR BEFORE I REASSEMBLED IT. THAT WAS EASY AND I CROSSED MY FINGERS ANY WAY. I GOT OUT MY NEW PART AND THE JET DRY I BOUGHT AND STATED TO FILL THE DISPENSER AND IT TOOK HALF THE BOTTLE.YEA !!! I PUT THE CAP ON AND COULDN'T WAIT TO DO A LOAD OF DISHES. EVERY THING IS LOOKING GOOD NOW. THANK YOU PART SELECT FOR MAKING GETTING THE PARTS I NEEDED SO EASY AND SHOWING DIAGRAMS SO I HAD THE RIGHT PART. I COULDN'T HAVE DONE IT WITH OUT YOU.

We unscrewed the old mount, and installed new mount, inserted screw and tightened. Waa-lah, that was all that needed to be done.

Followed the video. Only issue was that the panel mount screws cracked the plastic nibs that the screws threaded into. I replaced the screws with a Chrome sheet metal screw a bit longer and it held. Easy job!

Removed holding stew from old style bracket. Put arm together with new mount and installed screw. Aligned arm with upper rack and just clicked on. Ensuring spray arm spun freely and done!

WATCHED THE VIDEO FOR 2 MINUTES. REPLACED THE 3 PARTS IN LESS THAN A MINUTE. THANKS FOR THE VIDEOS.

Pulled the old gasket out with needle nose pliers, cleaned the slot for the gasket, installed the new gasket, needed no tools. This repair took 5 min.

Great fit. take out old one and drop in new one. Piece of Cake.

I ordered a dishwasher soap dispenser "lid assembly". When it arrived, it was not an assembly at all but only a lid. I had to reorder a pin and spring, When i finally had every thing, it was an easy repair.

Removed the plugs in the slides, removed the rack, slid the new rack in and replaced the plugs.

I bought the kit because it had other parts that I thought I needed.

I had already removed the old parts so when the new parts arrived, I just attached the water inlet tube holder and put the nut on the top of the sprayer assembly and it was good to go!!!! I ordered the parts one day before 3:00 and they were delivered the next day!!!! Unbelievable service!!!! Thanks and I am a very satisfied customer!!!!

Julie Welty

The old gasket around the door pulled out easily but was pretty nasty. While cleaning the channel out, kept finding more gunk that had built up. I decided to go ahead and take off the Inner Door. Used Torx driver to take off the screws. Found a tremendous amount of gunk built up. Was well worth taking the extra time to clean it all out. Replaced the Inner Door and put new gasket in channel. No more leaking!

Just removed the old lower dishrack and set in the new one. Nothing to it.

Followed instructions as the videos on this page show.

This spinner is attached to a plastic module PN WP3379369 which is held in place by two screws to the top of the dishwasher. I was able to temporarily reattach the spinner by using a hot soldering iron to melt the nylon axle that goes through the spinner. By using a very small metal washer placed on top of the spinner I was able to melt enough off the end of the nylon axle so as to keep the spinner in place and still be able to rotate. By far the most difficult part of this repair is removing the two stops that prevent the upper washer rack being removed from the machine. Doing so requires using a pair of long nosed pliers and taking note of what needs to be squeezed. Even if installing a new part the upper rack needs to be removed in order to get access to this central part.