66365490 Kenmore Miscellaneous - Instructions

I replaced the 3 screws because they were rusty. Then I replaced the Drain pump

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .

After removing the front cover and draining the tub, I replaced the drain pump and the washer works as good as new.

I took the front off by removing the two Phillips head screws at the bottom. I leaned the washer backwards and blocked the front up about 6 - 8 inches. Next I loosened the three screws that hold the pump on. Then remove the belt. Now it is time to get the hoses off by taking the clamps loose. Wiggle the hose and pull them off. You need a small bowel and towels to collect the water in the hoses. The final step is to take out the three screws that you already loosened that hold the pump on. The pump can now be lifted up and removed. Replace the pump with the new one and reverse the procedure.

I hastily (miss diagnosed) the symptoms by assuming that the Drain Pump was in fault, Ordered the Drain Pump part online on Sunday got it early on Wednesday. Installed the Drain Pump but the timer would not move. So back to drawing board. Got on the phone with the nice people on PartSelect ordered the Lid Switch Assembly. Got the part in less than 20 hours To install the Lid Switch assembly remove the back panel by removing 3 sheet metal screws at the top and 2 at the bottom now you will have access to all the wires and the Lid Switch Assembly. It is attached with one sheet metal screw. The hole in the Assembly is slotted so you may have to slide it back and forth for the switch to get activated when you open the door. Installed the part, plugged the washer machine in filled the tank. The washer machine came alive the timer was moving (the washer machine start working again). This washer machine should be good for another 20 years. By the way this was the first breakdown on this washer machine after 20 years of service. Thanks PartSelect for well trained people and prompt service I couldn't have done it with out your help.

The water pulley wheel kept seperating from the pulley shaft after numberous attempts with plumbers glue, the problem kept repeating therefor replacement was necessary. After ordering the part it was able to be replaced with the new pump and fast, washer running like new. Thank you so much.

I watched a utube video showing how to do the job. It was simple considering I am not mechanically gifted. The whole job took about 20 minutes. The hardest part of the job was moving the dryer out of the way first.

I removed 2 Philips head screws from bottom of front cover and removed cover. Tilted washer back and installed a 6' wooden block under washer. removed 3 hex head screws from pump base using my flex shaft nut driver and a 5/16" socket. Removed the 2 hose clamps from pump and lifted pump out. Pump appeared to be ok but checking by turning the pulley I found the impeller did not turn, shaft key must be sheared. The new pump came the next day at 2:00 PM and it was an exact replacement. Installed and up and running in about 15 min. Working fine.

Emptied washing machine tub with a small plastic bowl into a 5 gallon bucket, finihsing up last bit of water by soaking it up with towels. I next removed front panel on washing machine by unscrewing two screws on the bottom front, left and right, to gain access to the pump. Loosened two hose clamps and detached two hoses, catching remining water from washertub. moved washer out from wall about 3 feet and tilted washer back towards wall so I could access the inderneath of washer to lossen three bolts that held pump in place. removed belt from pum to motor and examined fro glaze or wear (none detected) and then removed pum and reversed steps to install new pump, reinstalling belt faily loosly, per instructions. Tried washer to see if ssue resolved and once confirmed, replaced the front panel. Have done multiple washes since then (at least 10) and no further issues. Very economical solution (under $100) and sense of pride with fixing applianmce myself. This web page was very informative and saved me a lot of money and time. Thanks!

1. Removed the front panel from the washing machine. This entailed removing two phillips head screws on the bottom left and right of the panel. Then, I pulled the bottom of the panel out and up until the top of the panel was disengaged from the machine. 2. Noted the belt tension on the old pump so I could install the new one correctly with the same tension. 3. Removed the two hoses from the pump, and the three screws securing the pump to the washer. 4. Installed the new pump providing the belt the same tension as I observed on the old pump. 5. Installed the hoses and tightened the hose clamps. 6. Reistalled the front panel and ran the washer. Works fine!

Once i figured out it would not drain i pulled the front panel off and pulled all the drain hoses off to be sure nothing was clogged there or in the pump itself. It was not so then i checked the drive belt and it was ok. Next i pulled off the drain pump and everything looked to be ok, it was not froze up and it would spin just fine. I got a screwdriver and held the splines inside the pump while trying to turn the pulley and thats when i found that the propeller was spinning on the shaft and under a load would only spin the shaft and not the propeller inside the pump. Got online ordered new pump and it works great now.

I am not going to describe the repair. The video that Part Select has on their website is exactly how our repair went. Very simple. This is the second time we have used Part Select. They have saved us a lot of money on repairmen or new purchases. I would definitely use them in the future. The videos are so easy to follow anybody can make the repairs. Also, the delivery company not only misdelivered the part but, they damaged it. When I called Part Select about the part being damaged, they immediately sent out a new part without any questions. Why aren't all companies this awesome?!

Pump was eazy to replace the clean up took longer than the fix.

I wached the six min. Video you sent me,so helpful what a great idea so the job only took me about five min. Thanks Mike

I took the front panel off and was able to easily access and remove the leaking drain pump. Then I propped the front of the washer up onto some boards so that I could put the two pulleys back onto the new pump, then I just tightened the three bolts in order to tighten the pulleys. However,when I started another load of wash there was a leak in the bottom of the tub, so I removed the new pump and went out and bought a new washer, figuring that our 13-year-old Maytag was going to cost more to fix than to buy a new washer. Then I wrapped up the new pump and sent it back. Thanks for all your help and for letting me send back the new part...I received confirmation of my refund today. Bob Trautman