Models > 663616

663616 General Electric Dryer - Overview

Sections of the 663616

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Drum Bearing Slide - White – Part Number: WE1M504
Drum Bearing Slide - White
★★★★★
★★★★★
(155)
PartSelect #: PS755842
Manufacturer #: WE1M504
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
$17.00
  In Stock
Drum Bearing Slide - Green – Part Number: WE1M1067
Drum Bearing Slide - Green
★★★★★
★★★★★
(27)
PartSelect #: PS6447706
Manufacturer #: WE1M1067
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
$11.49
  In Stock
Front Drum Bearing – Part Number: WE3M26
Front Drum Bearing
★★★★★
★★★★★
(74)
PartSelect #: PS960316
Manufacturer #: WE3M26
This Front Drum Bearing (Top Bearing, Dryer Drum Front Support Bearing, Drum Support Bearing, Dryer Drum Glide Bearing) holds the drum bearing and slides for the drum to turn on. The front drum bearin...
$59.76
  In Stock
Duct Felt Seal – Part Number: WE09X20441
Duct Felt Seal
PartSelect #: PS9861764
Manufacturer #: WE09X20441
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...   No Longer Available
BELT DRIVE – Part Number: WE03X29897
BELT DRIVE
★★★★★
★★★★★
(141)
PartSelect #: PS16542496
Manufacturer #: WE03X29897
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
$32.97
  In Stock
Selector Knob with Clip – Part Number: WH1X2721
Selector Knob with Clip
★★★★★
★★★★★
(71)
PartSelect #: PS271094
Manufacturer #: WH1X2721
The selector knob is what you use to start the dryer. This replacement knob comes with a retaining clip. This is a very easy repair, the only tool you may need is a pair of needle nose pliers. Remove ...
$17.22
  In Stock
Rear Drum Bearing Kit – Part Number: WE25M40
Rear Drum Bearing Kit
★★★★★
★★★★★
(17)
PartSelect #: PS267529
Manufacturer #: WE25M40
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
$67.72
  In Stock
Lint Filter - White Frame – Part Number: WE18X25100
Lint Filter - White Frame
★★★★★
★★★★★
(60)
PartSelect #: PS11767017
Manufacturer #: WE18X25100
This is a lint filter screen that is used for many dryers. It has a metal screen with a white plastic frame, and is approximately 13 inches wide. This part is sold individually. The lint filter traps ...
$68.19
  In Stock
Door Handle - White – Part Number: WE01X20419
Door Handle - White
★★★★★
★★★★★
(60)
PartSelect #: PS9494490
Manufacturer #: WE01X20419
This part is on the outer door of the dryer.
$20.68
  In Stock
Rotary Start Switch – Part Number: WE4X881
Rotary Start Switch
★★★★★
★★★★★
(19)
PartSelect #: PS268305
Manufacturer #: WE4X881
This part is used to start the dryer once you have selected a setting on the timer.
$57.88
  In Stock
Idler Pulley Wheel – Part Number: WE12X83
Idler Pulley Wheel
★★★★★
★★★★★
(6)
PartSelect #: PS265721
Manufacturer #: WE12X83
A dryer's idler pulley wheel serves to help the belt to rotate the drum.
$31.73
  In Stock
Timer Knob – Part Number: WE1X1263
Timer Knob
★★★★★
★★★★★
(14)
PartSelect #: PS266954
Manufacturer #: WE1X1263
This is a timer knob for your dryer. It is found on the control panel and allows you to turn your dryer on and adjust the settings. If the timer will not advance, or you notice the knob is damaged, yo...
$25.18
  In Stock

Questions And Answers for 663616

Ask our experts a question about this model and we'll get back to you as soon as possible!

2 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Ann
    December 11, 2019
    I have a beaumark mod 663616. My dryer made some stopped working yesterday. It still spins but has a very loud clanking noise. I am thinking it’s the belt maybe? What repair kit do you recommend?
    For model number 663616
    Hello Ann,thank you for your question. We would recommend replacing the PartSelect Number: PS1766009 Belt, and the rear drum bearing kit PartSelect Number: PS267529. I hope this helps.

    Was this helpful?
    Thank you for voting!
    Ann
    December 13, 2019
    Is there a substitute for the rear drum bearing kit partselect number: Ps267529?
    For model number 663616
    Hello Ann, thank you for writing. Sadly, there is no replacement information for it. You may want to reach out to GE directly for a substitution part number. Please feel free to get back in touch with us if they provide one. Thank you!

    Was this helpful?
    Thank you for voting!

      Common Symptoms of the 663616

      [Viewing 12 of 12]
      Noisy
      Fixed by
      these parts
      Show All
      Will Not Start
      Fixed by
      these parts
      Show All
      Will not tumble
      Fixed by
      these parts
      Show All
      Marks left on clothes
      Fixed by
      these parts
      Show All
      No heat or not enough heat
      Fixed by
      these parts
      Show All
      Door won’t close
      Fixed by
      these parts
      Show All
      Takes too long to dry
      Fixed by
      these parts
      Show All
      Timer will not advance
      Fixed by
      these parts
      Show All
      Shuts off too soon
      Fixed by
      these parts
      Show All
      Too hot
      Fixed by
      these parts
      Show All
      Will not shut off
      Fixed by
      these parts
      Show All
      Door latch failure
      Fixed by
      these parts
      Show All
      Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
      Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
      It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
      Parts Used:
      FELT TRAP DUCT Drum Bearing Slide - Green Drum Bearing Slide - White
      • Matthew from Plainfield, IL
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers
      765 of 868 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Intermittant squeaking noise
      Basically, I followed the same steps a prior person posted.
      1.Removed the two screws inside the door, on the top part of the opening.
      2.Lifted up and removed the top.
      3.Removed two screws holding the front panel in place.
      4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
      5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
      6.Checked to see how the old felt was installed, then I pulled out the old felt.
      7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
      8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
      9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
      10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
      11.Lifted up the drum and put the front panel back on.
      12.Screwed the front panel back on, using the two screws.
      13.Carefully put the top back on.
      14.Screwed in the two screws inside the front door to fasten down the top.
      That was it! I started up the dryer and it worked fine. No more squeaking.
      About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
      At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
      Parts Used:
      Front Drum Bearing FELT TRAP DUCT Drum Bearing Slide - Green Drum Bearing Slide - White
      • Mark from Addison, IL
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Screw drivers
      608 of 756 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Replaced broken START knob on dryer.
      Slid off the old START knob, then pushed on the new START knob.

      I created and printed a label on my computer for use with the time selector dial, which must be set at or beyond 10 minutes, before turning the START knob.

      I made a label that says "Minimum" with a red arrow that points past the 10 minute setting on the time selector dial.

      My teenage daughter was not setting the time selector dial, to a point past 10 minutes. When she turned the START knob, the dryer would not come on, because the time selector dial was not set past the 10 minute setting.

      My daughter had continually twisted the START knob until it broke. I am hoping she will be able to see the large printed label I put on the dryer near the time selector, saying "Minimum" with a large red arrow pointing past 10 minutes.

      I am very pleased that I was quickly able to find the exact matching START knob for my dryer and the exact same color, from PartSelect.Com
      Parts Used:
      Selector Knob with Clip
      • SAM from ROCK HILL, NY
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        Less than 15 mins
      495 of 505 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!