6500PRW Magic Chef Range - Instructions

Removed 2 screws, disconnected wires, attached wires to new element, put screws back. Turned oven on. Perfect.

I had the problem before and had to call in a Tech to repair the baking element in my oven. It cost me $150.00 for the repair. This time I decided to do the repair myself, so I went online and found this site The instruction video made it very easy. I am very proud of what I was able to do without calling a Tech. My oven works like new, It only cost less than $40.00 for the total repair. I am so glad this site were there when I needed them.. Thanks a Lot..

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

****Threw the breaker switch for the oven to the 'off' position****. Opened the oven. Unscrewed the phillips head screws at the back of the old element. Removed the connecting wire, taping them to the stove so that they wouldn't recede into the hole. Securely attached the connecting wires to the new element. Pushed the wires back into the holes in the stove. Removed the tape from the oven. Screwed the element into place. ****Threw the breaker switch back to the 'on' position****. Process took under 10 minutes.

DO NOT FORGET TO UNPLUG OR TURN OFF BREAKER BEFORE DOING ANYTHING WITH THE WIRES. Don't forget to turn it back on again when you are done.

It was so simple & the parts fit perfectly. I appreciated all the help from your sales lady. Thanks again.

First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.

First I removed the two screws that hold the element in place. I then pulled the element out aobut 3 inches and disconnected the wires.

I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.

I unpluged the old burner and pluged the new one in. Repair done in about 2 min,

switch off the range. undo the two screws & unplug the two tabs. Replace with new element, connect two tabs, screw back in place. done!
recieved my replacement part the next day after ordering

POWER OFF! Unplugged oven from wall.

(Note: I found it easier to disconnect the wires from the element by removing the rear cover. Fumbling around inside the oven was getting me nowhere.)

Removed rear cover.
Disconnected old element.
Unscrewed the old element from inside the oven, removed, and installed the new element. Screwed the new element in place.
Reconnected wires in back, installed the back cover.
Connected power.
Tested. Good as new.

removed the old element by taking out two screws then removed the two wires. pulled out the old element , put the new one in . connected the wires and screwed it in. Done.

I removed the two screws at the rear of the oven and pulled out the existing element, plugged in the new element, pushing it back in place and mounted the screws back in the bracket. I then made the "Tim the Tool Man" grunt noises feeling very proud that I am now officially a Handy Woman!

Easiest repair ever.

#1 - Turn off power (or you will get electricutued).
#2 - Unscrew back of heating elements
#3 - Disconnect wires (may need pliers)
#4 - Attach new heating element
#5 - Put in screws

Everything took 15 mintes max.

Turned off all power to range.
Removed two Philip head screws
Gentle pulled unit Element forward
Removed two push on connectors
(Do not let wires fall back into oven holes)

Reversed the process.