5MSF25N4BA02 Maytag Refrigerator - Instructions

We’d had the refrigerator repaired a year ago by the service department of our local appliance store. Turns out the service tech somehow used the wrong screw when replacing the door cam, causing it to rub on the cams and causing premature wear. After watching the provided repair video, it took about 10 minutes to remove the door, replace the cams and reinstall the door. Saved well over $100 and had the job done right this time.

I followed the instructions as laid out in the video associated with this fix. Aside from the fact that the video covers the freezer side door, the fix was the exact same. The video was outstanding and covered exactly how conduct the repair. Incredibly easy to follow and to do and required minimal tools. Wonderfully simple experience that saved a potentially significant amount of money to hire an appliance repair person.

Much cheaper than buying a whole new fridge. Tenant had broken many parts which some we were able to retrieve from one that had gone bad. Parts are expensive but much less expensive than buying a new fridge. We bought the shelf and the snack pan , took about 10 mins to put together.

Just opened the package and drop into tray frame

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Maintenance completed. Some difficulty.

Saw online info video explaining the possible cause and how to fix it. Ordered upper closing cam. Removed top hinge cover and hinge, removed door set it on a table. Removed old cam installed new cam tightened the retaining bolt put the door back on aligned it with freezer door and bolted it down snug. No more noise and it took less the half and hour.

slid the new drawer in place

DISCLAIMER: Technically, you should start by unplugging the frig and turning off the water supply. Though there is nothing on the my frig door that is either electrical or water related, the frig does keep trying to cooling an open area. For the short while I was doing the work, I just didn't want to bother with those precautions. Had I expected the work to take longer or been working on the FREEZER door I would have most certainly have done it "correctly." But I didn't do the freezer door so, first, remove everything from the refrigerator door storage shelves and the shelves themselves. Then lift off the cap that covers the hinge mounting plate on top of the frig. Remove the screws that holds the mounting plate in place. I used a cordless drill/driver with a 1/4" socket on the end but this could be done with a nut driver or socket wrench as well. Of course, take care not to let the door fall when removing the last screw. Then, lift the door off the bottom post that his holding it in place. The door is not too heavy and one person should not have a problem doing this but if you think it might be too heavy get someone to help with this. On the frig door there are no other connectors to be concerned with. NOTE: This procedure is similar for the freezer door but there are electrical and water line connections that need to be addressed before removing the door. Once the door is off the post, lay it down on a flat work service (I used the kitchen table with some towels spread underneath to prevent scratching either the table or the frig door.) There are two pieces that ought to be replaced. One cam on the door and one at the bottom post. Both are attached with a small screw that is removed easily with your nut driver/socket/drill driver. The bottom cam came offer fairly simply but sliding a thin, flat blade screw driver under it and prying it up and off. Replace this bottom cam with a new one and screw it back down. The door cam was, for me, the more difficult item. Removing the screw was easy enough but years of wear and brittleness led it to break off as I was trying to pry it out. I was able to use a small flat blade screwdriver to cave the old plastic post in all around the insert hole until I could get a good hold and pull it out with needle nose pliers. I was tempted to try to drill the old post out but there is a hex shape to the insert hole I was afraid of ruining. Once I got the old cam out, it was a simple matter to re-insert the new cam. Since both the door and lower cams are held on by screws there is only one way they can go back on. Once the cams are back in place, lift the door back onto the post and reattach the mounting plate to the top of the frig. Take some care that the door is level and parallel to the freezer door before completely tightening the mounting screws and replacing the cap that covers the plate. If you did shut off water and unplug the frig you should turn it back on and plug it back in. And do I really need to tell you to put the shelves and stuff back? :) The door should close on its own when close enough to the frig frame that the cam notches slide into place. If it hadn't been for the door cam being so brittle, this repair would have quite simple. Even at that, digging the old post out really wasn't hard but it did take some unexpected effort. If your refrigerator door is not closing properly, this is something anyone with basic skills can do.

First I removed the three screws on the top hing of the refrigerator door so that we could lift it off the bottom hing. Socket wrench bits for my drill made that fast and simple. I lifted the door off the bottom hing to find the door closing plastic cam to be broken in several pieces. The hardest part was getting the cylinder shape piece that had broken off the cam out from inside the door. This way we would be able to insert the new piece. Needle nose pliers are the right tool for that job since the hole is small and the plastic just frays under force from regular pliers. It took some force and patience to get that out, but once all the broken pieces were removed, reassembly was quick and easy

Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!

Opened the box, took out the new crisper, washed it, removed the old crisper, transfered the veggies to the new crisper, inserted the new crisper, closed refrigerator door! Threw away the old crisper. Done!

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.