5KSM193ADEVB0 KitchenAid Mixer - Instructions

I followed the video provided online. The model shown was not exactly the same as mine, but very close. The step-wise progression demonstrated on the video helped a lot. I had to double check the video a couple of times which added to the work time....I could probably do it again without the video in under 1 hour. As shown in the video, I laid out an old towel across two pieces of 2x4 which helped keep the mixer head in a position that was easy to work on and also prevented scratches.

simply put it together, .

watched instruction video (from Part Select), the demonstration was close enough to enable me to repair the mixer. Newer mixers are disassembled differently.

i followed the instructions in video. Thank you joe

I how the video for replacing the worm gear on your website. It help me a lot. I followed step by step instruction display on video. It was great help.

I was very happy with the customer services department and the support I received in identifying the part I needed for the repair. I received an email confirming my order with all details. I do wish you had a more cost effective shipping alternative, like Priority mail.
The repair went well and the mixer is back in business, for making those Chocolate Chip Cookie and brownies if you know what I mean.

Thank you
Ron Ashby

After I dropped a part of the shield into my mixer the motor screamed and I unplugged the mixer. I found out I had a broken worm gear. I then order the part and per the helpful video I did the repair and I also changed the brushes my mixer is up and running waiting for the holiday baking season thanks to Part select.com Very easy Instructions to follow I am very happy with the results. Thanks Barbara

Replacing the base retaining bracket(what KitchenAid calls the screw cap) solved the problem immediately. The entire replacement effort took no more than a minute requiring removing 3 screws, discarding the old base, putting in the new one, and putting the screws back in. PartSelect was very easy to do business with. They shipped the part the day I ordered it and it arrived as scheduled. Can't be easier than that.

and I thought replacing the hinge pin would fix it, I used an awl to push out the old pin then used the new pin to push the old one all the way out. That did not fix the problem. Went to a store to look over a new one and saw that the screw under the head at the hinge point on the new machines was not screwed in tight. Turns out that screw is the "bumper" for the head against the neck, so the head is held back by the screw. FIXED

1. Removed the mixer from the base by removeing the pivot pin at the mixer base support. 2. removed the retainer ring from the housing. 3. removed the pin from the shaft. 4. removed 5 philips machine screws from the round base. 5. removed the round base from the mixer housing. 6. removed the o-ring from the shaft. 7. removed the shaft and large worm/pinion gear from the shaft. 8. pressed out the pinion drive gear from the mixer. The reverse operation repaired the mixer to new condition.

Order part through parts select. it only took 3 days to receive part. The mixer was very easy to take apart and to replace the gear. it was back together in about 20 min. The video from kitchen aid to repair the unit is awsome. Thanks

I replaced the brushes. I didn't realize that I've put one of them wrong. Reminder for next time the brushes have to touch the rotor of the motor. It took me a little bit to understand but the brushes can go in and not touch the rotor. It works very quietly now. Thank you PartSelect for your infos and knowledge.

Just change the motor brush. That's it! It work well now. Thank you, Partselect!

Knob fell out of the front of the mixer into the bowl and jammed the beater. This caused the motor to strip the plastic worm gear. Open unit to investigate and found about 4 teeth missing out of the worm gear. Ordered a replacement. Installed the new gear once received in about 30 minutes. Wife is now happy again. Just need to make sure you pack enough gease into the new gear before reassembling the unit.

The plastic worm gear was stripped,I took it apart first then cleaned out all the old grease so when the new part came it together like a charm.