5KSM193ADEVB0 KitchenAid Mixer - Instructions

Took the mixer apart and cleaned the grease so off I could see the pins. Wasn't a hard fix only thing is make sure to clean the grease off so you can see what your doing

Obviously the problem was in the gear box of the mixer. I disassembled the gear box by removing the four large screws holding the base then the four screws at the rear and center of the mixer. Then I removed the thin metal ring covering the five screws around the front of the housing by gently prying up with a small screwdriver. The five screws beneth the ring have to be removed with a small blade screwdriver turning them a round at a time in sequence until they are free. Gently pry the two housings apart with a screwdriver and lift our the lower half with the plantary gears. I found the drive gear was stripped. I went to PartSelect on the web, eaisly found the exploded view of the mixer's gear box and ordered the gear I needed. The gear is part of an assembly attached to the mixer housing with three screws. Work around the lubricant in the housing. Within four days I received the new gear, installed it by reversing the above procedures and the mixer is working again. The total cost was $34.85. Not a bad investment considering the mixer cost over $400 and would have been trashed for want of one part.

Followed step-by-step video instructions for dis-assembly/reassembly found at ereplacementparts.com. All went well except when driving out the pin that holds the worm gear in the tower. The video wasn't exactly clear enough about what position the pin should be in when driving it out and I inadvertently drove the pin out so that it was trapped inside the tower assembly. Result? I had to bend the pin to get it out, causing an extra expenditure and wait time to order a new pin. So, lesson learned: be sure the pin is horizontal to the tower and not perpendicular to when driving the pin out. Also, I found that having the mixer apart was a good time to replace the grease in the housing. I don't think it would be required to replace the grease at this time but I was worried that pieces of the old worm gear could remain in the grease and possible get jammed in the gears after repairs were completed. Be sure to get a "food grade" grease not grease from your local auto parts store! The table knife was the best tool to use to remove the grease and to smear the grease all over the internal gears when replacing it.

Inserted new pin and tightened set screw.

Took out 3 screws, removed old plate, put down new plate the tightened screws. Runs like new, great service, price, quick delivery!

Turned the mixer on its side and slid the part into the bottom of the base.

I called my fiancée.

Three phillips-head screws held the "Cap Screw" in place on the stand of the mixer. After cleaning the stuff out of the screw slots, the screws came out surprisingly easy. After the plate was lifted off, we cleaned the residue from under the plate, placed the new one in position and easily screwed in the 3 screws.
We were very pleased by the quick delivery of the part.

removed the screws holding the mixer housing and then removed the worn worm gear by removing the roll pin holding it on the shaft. Replaced the worm gear and inserted the pin that hole it in place. Replaced some of the gear grease and reassembled mixer. Went very easily. No problems at all.

Place Pin in hole where it was missing then gently tap pin into place
Run a test and all is good ??
make sure to use a drift pin set
Tom

remove the back cover part # 36, remove the top cover part # 1 (by removing the chrome ring parate # 28, the mobile disk part # 25 and six screws part # 24). This done, remove the system parat # 38 to release the Pevel Pinion Center Gear part # 15 and remove the damaged part and put the new part. The install the removed parts in reverse order as they withdrew.

Punched out the roll pin to remove eccentric from spindle, undid 5 screws (after removing trim ring), and removed 4 screws to undo the motor housing. Make sure to keep the one screw with a lock washer in the BACK of the housing. Undid the screw on top to remove the back of the motor housing to take out the strain relief grommet, prior to removing the motor housing. Scraped the excess grease into a tub to re-use. Pulled out the shaft, and lifted out the old (stripped) gear and plopped the new one in. Make sure to mark match points for parts, and put the pins back in in the right order. You have to put the 5 screws back in before sliding the trim ring on, and putting the roll pin back. make sure all gears mesh and test before snugging the motor housing screws. Be sure to orient the strain relief grommet securely, and be careful of the filter plates in the back of the housing (they're brittle). putting the grease back is like frosting a cake. Save a little for the planetary ass'y.

Literally the whole top of this stand mixer had to be taken apart. With the help of U-tube! We realized the silver strip was removable and there where screws underneath. We figured we would replace both parts while it was all taken apart. We cleaned the mixer and added some grease where necessary. I now have a 25 year old new mixer. Thanks for having our parts and guiding us with a diagram of the unit. Very helpful.

Repairing/replacing worm-gear (FSP part# W10112253) for a KitchenAid Stand Mixer model number K5SS. First: I am writing this story because all the videos or repair articles I’ve viewed are either misleading or incorrect in that they do not include older K5SS models. 1. These older models from the mid 1960’s or even earlier have four very large #4 chrome plated Phillips Head Screws holding the mixer base to the motor assembly and NOT four small machine screws (one with a lock-washer) as seen on other repair videos. In addition, the stand is composed of two separate pieces with the bottom half being held together with another four identical #4 chrome plated Phillips Head Screws. The upper four holding the stand to the motor housing (I used a manual impact driver to loosen the very stubborn, #4 Phillips screws) must be removed so as to access the four smaller Phillips machine screws (no lock-washers found here, best buy at least four #10, split, before reassembly) 2. Lastly, you will need two pin punches however the recommended smaller 3/32 inch is still too large to remove the pin in the tower assembly. You will need one size smaller or a #4 pin punch instead. These older Kitchen Aid mixers were built with very tight tolerances. Please be patient and take your time removing the pins. Good Luck……. Jim

I removed the pin from the outside shaft,then removed all screw around the body of the mixer,then removed the top case out,took 3 screws out from the the gear assembly case......punched the pin out of worm gear then release the little shaft out from the case,replaced a new one....then starting go backward till completely all assembled don't forget lube grease to all gears and test run good very smooth.........it's ok