59672003010 Kenmore Refrigerator - Instructions

Watched the video on this site, followed the instructions to lay the gasket flat and warm it with a hair dryer, removed the old gasket, and popped the new one in. Easy!

I followed the remove and replace instructions in the Part Sect video when I ordered the seal. Pulled out the old seal by hand and installed the new seal. No tools needed, very easy. Took 10 minutes at most.

Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.

Received gasket. Checked color and size. Because this unit is 33 inches wide one door is 3 inches narrower than the other. Removed shelves from door to provide more room to work. Took 15 seconds to pull out old seal and 1 minute to install the new one. Checked to make sure center sealing flap were on the center side of door. Started in upper corners, worked my way around the perimeter pressing in in with my fingers.
Took longer to R&R and wash shelves than to replace door seal.
VERY EASY

The parts were very easy to replace, however I am still without ice and cannot figure out why. I have ohm tested the contol unit and everything works fine, I am able to jump it and turn on the motor and water fill valve. Any suggestions?...

gasket pulls out of groove in the door very easily. insert new gasket in the groove. very groovy!!!!!

To repair the problem,I ordered a new gasket. Once I received the gasket, I laid it flat on the floors and hot the blow dryer and blow out the creases in the gasket. I then took off the door by removing the four screws from the door and rest the door on the table. I then removed the old gasket and replaced it with the new one. It took about 15 minutes. My frig. Stop freezing up.

Talking with the service tech and youtube video it was a snap... Saved a service repair and a 25% parts mark up..

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Turned off power, Removed screw, disconnected wire harness and removed old rail from door, Connected new wire harness and attached new rail to door, replaced screw. Restored power. Done.

Easily pulled out the gaskets off the refrigerator doors and replaced them with the new ones. The installation video was also a big help in the process.

I watched the video and it took away my trepidation. I did what it said and it went right in!!

My freezer compartment gasket was torn and needed replacement. This was on a bottom freezer Kenmore refrigerator. I couldn't find directions for how to take the freezer compartment door off, and figuring out how was the hardest part. Here are the instructions:
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.

Replacement gasket extremely easy to install. Used hair dryer to soften and straighten out “kinks” in replacement gasket. Pulled old gasket out of groove in refrigerator door. Lined up corners of new gasket and pressed into place with my fingers. Went in exactly as video showed.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.