5871641591 Kenmore Dishwasher - Instructions

I removed the 2 screws that hold the dishwasher in so I could pull it out. I found out later I didnt need to do this. then I removed the bottom cover and saw the spring that was broken. I removed the spring, hooked the new one into place and I was done.
This was the easiest repair I ever had to do.

pulled the old gasket out, and pushed the new one into the slot where the old one came out. Very simple repair, and I'm a girl!!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

I used the scissors to open the bag the gasket came in. From there it was just seeing how the old, worn gasket was seated in the track around the inside of the dishwasher. Pulling the old one out and snapping the new one in the same way. When I was finished, there was about an inch between the two ends at the bottom where the gasket wasn't quite long enough for them to meet. I was a bit concerned seeing the basin fills with water. So I cut an inch off the best part of the old gasket to fill the space. No leaks! It works great and was so easy to do.

Remove the old gasket simply by pulling it off. I installed the new gasket by starting in one corner and simply pushing the gasket firmly into the groove and working my way around. No tools required. My child could have done it. Problem solved. It takes two or three cycles for the gasket to "break in" and form precisely to the door. Leave the door locked a couple of days to hasten the "break in".

I read the instructions that others had posted and completed the repair in less than 5 minutes!

if the wire they snap on was bent it needs to be straightend.......they just snap on. easy to install but wish they had better wheels so this problem would be solved. My 2 sons have same brand dishwashers and have same problem.

Removed the lower panel (two screws near the floor, two screws with the door open).

Remove screws holding the top of the dishwasher in place.

Remove two screws holding the incoming water switch.

Pull the dishwasher out to access the left side of the dishwasher.

With the door closed remove the spring (replaced both left and right).

Test the motion of the door.

Reverse the process
1. push dishwasher back in
2. Attach water switch bracket
3. Attach top screws that hold the dishwasher in place
4. Replace lower panel
5. Attach screws for lower panel

Test the door motion,

I replaced the gasket a couple of years ago for less than $50. The springs with shipping for less than $25. I wonder how much longer the dishwasher will last. The repairs are easier than putting in a new dishwasher and a whole lot cheaper.

My dishwasher started leaking at the beginning of the summer. We didn't know what to do, but didn't want to call an appliance repairman. Towards fall, a friend came over and pulled it out and found the heating element brass nut which was broken. We put it back in and washed dishes the old-fashioned way for another 3 months after that. I asked at my local hardware store for the part, and thought about trying one of those big-box do-it-yourself stores but never got around to it. Finally after getting sick and tired of doing all the dishes in the house by hand, I found your site, and the part I needed and ordered two (just-in-case). A few days later, we got the part, I pulled the dishwasher out again, screwed on the new nut by hand and put it back into place. We're in business!

1) Soaked new gasket in hot water for about 15 minutes to make it more pliable. 2) Cleaned accumulated soap residue from gasket area. 3) Removed old gasket by pulling it from machine. 4) Installed new gasket starting at the top and aligning notch on gasket with center of top door latch. 5) Pressed gasket into place working from the top to the bottom. 6) Inspected and found about a half inch gap remained at bottom. 7) Cut a piece of the same size from the old gasket and pressed it in place to close the gap.

Removed bottom cover , PLACED TAPE ON SHARP EDGES OF ALL METAL!!!!!!! Pulled electrical connections off with long reach pliers , removed old split nut ,it was loose !!!!!! . Placed new nut into deep socket , started by hand until sung ,then attached small short 1/4 ratchet to socket and took two (2) turns . Reattached wires with long pliers, Tested on short cycle and nooooo,leaks !!!!!!!! SAVED HUNDREDS OF $$$$$$$. Replaced lower cover .ITS NOT ROCKET SCIENCES. GET AFTER IT !!!!! Bill.

There were 4 zip ties holding old silverware basket on to bottom rack snip them, remove basket install new basket with zip ties both ends 2 more in middle about 1-2” apart. Try to install ties about 1/2 way up on basket so it doesn’t get top heavy.

This site had good pics and descriptions of the gasket I needed, as well as a LOT of users instructions concerning installation. Ordered, came quickly. It was a little hard to push in the groove. (Maybe a little silicone lube on the gasket would help??) I also filled in the gap at the bottom with a small section of the old gasket, as suggested by (other) installers. Why not? Anyways, it took both hands to close the door the first 3-4 washes. Easy to open/close now. AND... no more leaks! Great price, too!

I called an appliance store and they said to bring in the model number and a deposit and they would order it for us. Then, I decided to go to the Internet. I Googled Gibson Dishwahers and your page came up. I entered the requested information and ordered the gasket. In LESS THAN 24 HOURS it was delivered and in les than fifteen minutes, our son installed it. No more leaks! Thank you for the excellent service.

Isolated the leak and found the nut had split thereby allowing a loose seal and water penetration. Ordered 2 nuts just in case the other goes and the installation was easy. Unplug the unit, remove baseplate, remove screws under the countertop, and slide the unit out a bit. Use needlenode pliers to remove terminal connection and replaced nut. Reverse it for assembly. 3 minutes tops $6 later it is done. Easy money saved by a DIY.