5871440190 Kenmore Dishwasher - Instructions

I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.

used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

The parts arrived 20 hours after ordering -great service & the parts were just like like the removed parts only new. The old door gasket was pulled from its groove & and the new gasket was installed witout using tools. No more leaking water.The door spring installation wesa bit more difficult. The front bottom was removed with a nut drive, the broken springs were fished out, new springs were pull onto the arms and the cover put back in place. Not a bad job for a crippled, one-eyed 82 year old man.

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

I ordered a new door gasket and door spring. I unscrewed the two screws that hold the dishwasher in place and pulled it out. I pulled the old broken spring off with pliers and installed the new one ,,,very easy. I then took the new door gasket and soaked it in hot water in the sink for 15 min. That made it very soft and pliable to work with. I used pliers to pull the old gasket out then cleaned the area around the old gasket where crud had built up. I pushed in the new gasket working from top to bottom one side at a time. Turned it on an ran through a cycle and it works perfect now ,,,no leaks.

Removed lower panel; unmounted fill valve assembly. Installed two springs. Remounted fill valve assembly and reinstaslled the lower panel. Door must be in a near closed position to gain access to the door "L" spring brackets.

Simply remove the bottom panel below the door. The owners manual (22 year old model) showed the proper hole in which to attach the spring. Attach spring to door and then to frame of dishwasher, as illustrated in manual. It is a tight fit to get your hands in there, but once you do it is a snap. We have replace these springs several times over the life of this appliance, this is the first time we have actually found the proper springs, should last a long time. Thank you Parts Select for having the inventory for such an old model!

This dishwasher has a plastic bolt that holds the actuator on. The action loosens the bolt and it wobbles and eventually comes off. After enough attempts the bolt will strip and need to be replaced. I took some 3M loctite this time to hold it in place. It is 24 years old, but still kicking

I only had one break, but bought both to replace. I don't agree with those that say you have to slide the dishwasher out to repair. I simply removed the lower kick plate, and replace the springs in no time. Very easy as was ordering the parts. I will return here for all my appliance parts in the future. Hope I don't actually need any.

power off, take off kickplate, unplug 2 wires and unscrew broken nuts, put new nuts on, plug wires back in,(run dishwasher one cycle to make sure no leaks) put kickplate back on, power on.

Ditto the other comments. Easy, great savings. Perfect. Thank you!

Pulled the old gasket ou, cleaned the groove with a cloth. Then pushed the new one in, starting at the bottom. The curvatures are clearly marked, no guesswork.

Spotted the source of the leak at the first heating element under the dishwasher. Removed the brass mounting nut and it was cracked. Replaced with new part from PartSelect.com and the leak was fixed. Apparently the heating element gets so hot it tends to crack the mounting nuts, which results in a leak. Delivery time for part said 3-5 days - mine arrived one day after ordered!

Removed old gasket and clean surfaces on tub and door before installing new gasket. New gasket has a small notch in the middle for top center. Install top then down sides for best results. Door gasket snaps into existing groove so no tools are required.