52170128 General Electric Washer - Instructions

Removed the back of the machine and then flipped the machine on the side and loosened the motor to get the old belt off. A piece came out so we had to check the schematics online to figure out where it went. We believe it was the out-of-balance cut off switch. So to fix that we unplugged the motor assembly and took it out. I also had to fish the spring out of the vacuum, no small task. The worst part was that the belt was so deteriorated that it was super greasy and the carpet ended up a mess. We replaced the motor and belt and now it actually gets the water out of the clothes. Simply Green cleaner was used for the rug and after some strong elbow grease it was cleaned. If not for the mess and the other part and the vacuum snafu, I would have labeled this as easy.

Laid washer face down, unscrewed the 3 screws holding part to brackets. Removed the hose connections to the pump part. loosened the clamp around the base of the pump and pulled the part out. inserted new pump, tightened the clamp, reconnected the hoses, and bolted the part to the brackets. First time through, one of the hoses was not tight enough, so we put a new clamp on it and it worked fine.

Viewed video on installation of new belt. A little awkward to get to the rear bolts, but used a wrench with success. Now washer spins correctly. Thank you.

Took agitator out of machine knocked old coupling out and inserted new one into agitator/washing machine. Part arrived promptl and correctly. Thank you. JD

I disconnected two wires on back of inlet valve,then I removed the plastic hose connected to left side of valve. Removed old valve and replaced it with the new one.Attached hot/cold hoses and turned on washing machine to check for leaks.

Took the back cover off 6 screws, took the inlet valve off the mounting plate 2 screws, the vater valve off the mounting plate 2 screws, and disconnected the inlet valve clamp from the inlet hose to the washer. In reassembling reversed the process. Best part; G.E. was going to charge me $59.00 for the valve, and I got it for $16.10 shipped in one day.

I removed 2 screws on the top control panel to tilt the panel back. Then "popped" the hinges. I then removed 2 screws on the rear panel, to "pick up" the panel out of its locking position. Then the rear panel was loose. I removed the 2 srews holding the water inlet valve to the panel, removed the hose and placed the new water inlet valve in position. Assembled everything back to gether. After a $16.00 part was replaced, the washing machine worked like a brand new one with very high water flow. It was a very simple task to do on your own.

My appliance repair man replaced the inlet hoses into the washing machine and in doing so damaged the threads on the hot water inlet which resulted in a seriuous leak. I removed the 4 screws that held the damaged water inet valve (#PS270305)in place (inlet valcve and solenoid), removed the 4 wires to the solenid (noting the order in which they wree attached) and simply reattached the electrical wiring and screwed the inlet valve in place with the 4 screws that I had taken off to remove the old part.

I changed the Water Inlet Valve in less than 15 minutes. The valve fit exactly, and the water hoses fit right on. I turned on the water and the washer filled without hesitation. The cost was 15.00, this beat the 62.00 price I was given by GE for the part alone.

I did watch the video, that Parts Select included in an email. After that just follow the instructions in the video. You do need two people to do the job, since the belt needs to be tight. One for holding and one to tight the screws.

i Had washer up side down took puly out and transmission seal out used screw driver install your part add seal on it tap it back in used socket added quartz of gear oil90 as recommended put every thig back it good experience and saved hundreds of dollars for new ones thank so much for ur video and ur technical people on your site

Could smell burning rubber as it tried to spin, so figured it was the belt. No, I did no do it the hard way by removing the screws etc. I threaded the belt on the pulleys on one side, and slowly turned them, using my fingers to force thread the belt into place. Worked like a charm.

I had to tilt the machine to gain access to the screw that holds the yoke bracket in place. Then I removed the one screw that holds the yoke bracket and removed the yoke and it's cushion. I then had to remove the two friction pads from the old yoke and install them on the new yoke. I was able to re-use the old yoke cushion and after re-assembling the yoke and cushion, I installed this assembly with the one screw. Righted the machine and the job was done.

turn off water outlets, unplugged unit then removed water hoses, then removed the screws from the plate on the washer then removed the valve from the plate then unscrewed the clamp for the water inlet to the washer then removed the hose. then carefully removed the wire clips putting each one on the same connector on the new valve, then put everything back like I did when I took it apart and it works great.

I emptied the washer and unplugged it from the wall. Then i pulled it out so I could get behind it. Next unscrewed the water hoses from the washer. Removed the plate holding the water inlet valve by unscrewing 2 screws holding it to the machine (I used Vise Grip/pliers). Note which side of plate goes up/outward so you can put it back on! Removed 2 more screws that hold the valve to the plate. Remove clamp from valve end to disconnect valve from tubing with a screwdriver. I was able to remove the tubing with a twisting motion even though my washer is way over 10 years old. Remove 4 electrical clips from the valve by pulling them out, (REMEMBER the order of the electrical wires!!). Install new valve by doing this in reverse. Then run test cycle, success and saved hundreds of dollars!