4822A Frigidaire Range - Instructions

using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine

The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!

Very quick and easy fix. Used a nut driver to unscrew the bolts. Pulled it out and disconnected the two wires. I was very happy with the wonderful service we received from Partselect.com. I ordered the part Sunday evening and the part was here Tuesday by noon. I payed regular shipping charges. What a pleasant surprise!

Unplug the oven, open the door, take the screws out of the back wall that hold the small brackets which hold the element. Pull the element out of the wall, and pull a little of the wires with it to grasp easily. There are square nut screws, so you need the appropriate tool. Unplug the old element from the wires, and plug the new one in. Screw everything back together! This was a very easy fix!

Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE

My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You

the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.

Remove the old one and replaced the new one. It was very simple, fast, and easy.

Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!

unfastened clip at back of oven w/screwdriver. Pulled out the plug, unplugged the element. Plugged in new element, pushed back into place, refastened clip to hold it in place at back of oven.. Done

1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.

Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.

Just followed the very simple video instructions…it took less than 5 minutes.

All that was needed was to unscrew two screws holding it to the back of the oven and pull it out to get to the wires. Then unhook the wires and install new one. Less than 2 minutes.