480447D Frigidaire Range - Instructions

removed the two screws pulled the wires out sliped the connections from the old element and connected the new one .

For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!

Removed the screws, replaced it with the new bake element, put the screws back in........and bam! I'm back in business. That's how easy this was to repair. Bake element cost me 40 bucks, appliance repair shop wanted about 200 bucks to repair.

Unplug the oven, open the door, take the screws out of the back wall that hold the small brackets which hold the element. Pull the element out of the wall, and pull a little of the wires with it to grasp easily. There are square nut screws, so you need the appropriate tool. Unplug the old element from the wires, and plug the new one in. Screw everything back together! This was a very easy fix!

Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE

Turn power off. At oven, removed two screws from element hanger. Pulled old element out exposing spade connectors. Pulled connectors lnstalled connectors on new element and shoved back in stove and replaced screws. Work done with oven door open using drop light. Check for debris, turn power on, turn oven on to check.

Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY

The repair took less time than finding the model number. After unplugging the range and allowing it to cool I disconnected the element (2 screws), went online and found Part Select ordered the element and saved $16.00 dollars over the least expensive local shop, I was amazed at how fast the element arrived, I believe it was 4 days from order to my door. I went to my local hardware store for some new connectors for the wire, put them on and plugged in the element fastened down the two screws and went back to baking cookies. The element was well and safely packed and came in perfect condition. It works like a charm. Thank You

Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!

Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.

My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

Very simple, 2 screws, replace element, put screws back into place. The BEST thing... ordered on Tuesday afternoon, received on Wednesday afternoon, and Thursday was New Years day. This has been the best service, from any parts company, that I have ever ordered from. Keep up the good work!

Unplugged oven, pulled out old element, reattached new one, making sure to be careful with wires, and put on as secure as possible, just like it was before. . . Very easy to fix

Take out 2 screws disconnect the wires one on each side removed element recoonnected the wires put the 2 screws back in . Also I did flip breaker off while working. When I turned the oven on I noticed it gets bright red almost instantly. I dont remember my old getting red at all. this tells me it probably needed changing a lot earlier. I ordered the part sunday nite it arrived wednesday at lunch.I will definetly use this co again.

removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done