41549 (ASRESEU) LG Washer - Instructions

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.

1) Shut off water supplies 2) Unplug 3) Disconnect water supplies from back of washer -some water will dribble out 4) Unscrew 2 screws at back of washer top plate (the lower of the two screws on each of the plastic bumpers) 5) slide top plate back a couple inches, then lift off. 6) Carefully stuff a towel underneath the distribution hoses and valves to catch any water that escapes during replacement. 7) Snap a photo of the entire area to help identify where the hoses and electrical connections are located to aid in re-connection (or label with tape). Be sure to note the color coding on the wires in relation to how they connect to the valves. 8) Pull the electrical connector(s) off the valve assembly 9) Use pliers to loosen and slide the hose clamps off as many of the hoses as possible and pull the hoses off the valve assembly. Some hoses are hard to reach, and can be removed after the valve is detached from the washer housing. 10) Unscrew the two screws from the back of the washer body holding the valve in place. 11) Remove the valve (and any remaining hoses). 12) Attach distribution hoses to new valve 13) Place new valve into washer body and screw into place. 14) Reattach electrical connection(s). 15) Remove towel and check for any stray water 16) Place top cover on washer and slide forward to lock in place. 17) Replace screws in top cover at rear of washer (unless you plan on checking for leaks after testing) 18) Reattach water supply hoses 19) Turn on water supplies 20) Plug washer in 21) Run washer self-test to check that all water inlets operate -see note at end 22) Check for leaks at water inlet hose connections and underneath washer OPTIONAL but ADVISABLE: check for internal leaks - 23) Unplug washer 24) Remove top cover 25) check for leaks at distribution hose connections 24) Replace top cover 25) Secure screws in top cover 26) Plug in washer NOTE: Washer self-test instructions: Turn washer off. Press and hold the SPIN SPEED and SOIL LEVEL buttons simultaneously, then press POWER button. Keep holding SPIN SPEED and SOIL LEVEL buttons until buzzer sounds twice. Release buttons. Press START/PAUSE button 4 times to test prewash inlet and listen for sound of water entering the washer. Press START/PAUSE button again for main wash inlet, press again for hot inlet, press again for steam inlet, press again for bleach inlet. Press 4 more times to get to drain cycle and watch for water to drain from tub (if any visible). Press 3 more times to turn test off. Power off washer to reset.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!

I watched a YouTube video on the repair and I was fully prepared.the repair went easy

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

Super easy to find the part thanks to their diagrams. This fix was easy but I would definitely use this site again.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

greate very easy and the parts fit awsome the shiping was fast and easy very satified

Took apart the washer and removed bearings and shaft on spider. My advice would be to order the spider and shaft (one piece) hen ordering the bearings, seal, and tub gasket. If the bearings are gone, it is likely the shaft is gone too as mine was.

Contacted LG customer service, not much help there. Watched a very helpful Utube video on how to find and repair the leak. The video suggested that the most common leak is in the drain hose with bellows. Removed the rear panel and removed the bellows unit using pliers for the clamps and screwdriver for the bellows part. This was pretty easy. The rubber bellows was leaking in the exact same place as the youtube video showed. This is a Design Flaw that LG needs to fix. Ordered the new part and installed the bellows portion of the part first, as the angle for that installation needs to be correct. Then attempted to install the end of the hose (very inaccesible) to the pump drain. Very difficult to position the factory supplied spring clamp with pliers so I purchased a screw-type clamp (using the nut-driver rather than a screw-driver to tighten the clamp was helpful) at the local hardware store and that made my job much easier. Note: My unit is mounted on a pedestal, so it was a little easier to access the part location (about one foot off the floor, rather than at floor level), but it may be that the part should be replaced from the bottom of the unit, which would make it much easier to access. Then I installed the other end of the hose to the drain line using a screw-type clamp. I am 69 years old, and not that flexible anymore, so getting down on the floor to reach inside the unit was difficult. You need patience to do this job and you have to make sure all the clamps are properly installed so you don't start the machine up and end up with another leak. For me, this process was difficult and took more than two hours to complete. Limited access to the area made it more difficult and I hate the factory clamps they use. Overall, the repair costs about $25, compared to the $125 just to come look at the machine, then more money to fix the unit. It was satisfying to complete the repair for a small amount of money, but not sure it was worth the aggravation.