41549 (ASRESEU) LG Washer - Instructions

Use just your finger to push it into place. VERY EASY

Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.

Took front of machine off to access 2 shocks, put back together then removed panel in back to access third shock, watched YouTube video first so things went smooth

Had to manually shut off water valve behind the washing machine to stop the filling process. Followed repair video from the website.

I looked this problem up on YouTube like I do with everything, I saw a video from this site.. so I ordered what I needed from the website. The parts came in I unpluged the washer from the wall very important, I literally removed 6 Philips head screws and unclipped the wires from the parts and removed the hoses with the pliers, hoses have squeeze clamps. Put in New parts put hoses back on wiring back on and I was done.. it took me a total of maybe 10 minutes.. NO MORE WATER standing in the washer.. Thank you!! I would recommend you add a video for the Inlet Valve Assembly like you have for the hot inlet valve though...

Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.

you tube it , not to hard to install

Disassembled washer, replaced bearings, seals and gasket. Watched instructional video to familiarize myself with the repair. Followed all steps as recommended, repair was straight forward without any surprises. Hardest part was removing the drum from the machine, somewhat heavy. Disassembled and replaced all bearings, seals, spider and gasket. Reinstalled in reverse order. Note: Upon tear down, I found the seal was pushed out, causing the bearing failure. I also found that the seal was installed incorrectly from LG. They have the seal lip facing the bearings, should be facing the water. This repair seems to be difficult, but was fairly self explanatory. All plug ins are color coded, all hoses are accessible with little effort. If you have basic skills you should be able to handle this repair.

I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.

Just removed the top cover only. Reached down and unplugged the door switch. Then removed the switch with 2 phillips head screws. Replaced with new switch. Reached down and plugged that new switch in. Problem solved!

From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 seconds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.

I ordered the Rotor Assembly and Sensor Assy..
Rotor Assy. was not the problem.
1 - 17mm bolt in the center of the rotor assy.
6 10mm bolts to take off the Stator assy.
once you have the Stator assy off, upplug the sensor assy and release the clips on the sensor assy. and remove.
Install the new sensor assy. and plug the electrical connection back in.
replace the 6 bolts and screw the bolts evenly around the Stator.
replace the Rotor Assy. and secure the 17mm bolt.
Replace the back cover (4 - philips screws.
Do a test load.

pops right into hole

Took the sealing ring off the gasket, unscrewed the door lock with two screws. Unplugged it. Plugged the new one in, screwed it back in. Put the ring back on and it started right up.

The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!

It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.

Please note that the washer should be unplugged from power while working on any electrical component.