Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dead spot in motor/pump seal leak
I had a problem where the GE dishwasher would randomly stall upon startup due to a dead spot in the motor which prevented it from energizing. I removed the dishwasher's bottom access panel to inspect it and found that not only was the motor dead but it had a sizable leak emanating from the pump seal. I removed the dishwasher from under the cabinet area and turned it over to make it easier to replace the motor and pump assembly which only took a matter of minutes; the most difficult part of the repair being the reinstalling of the dishwasher. The replacement motor/pump assy was not only modified from the original parts but it is also much quieter than the original. I also have to commend PartSelect on their very speedy delivery which was only 2 days. All in all with a couple of minor modifications that was taken care of with the included parts the repair went very easy.
Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.
dishwasher was filling up .but it was,nt washing .had a repair man looked at it and said it needed a seal .so we bought it and install it our self and .it wasn,t that it was the moter .instead of a seal .
took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .
replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.
Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.
The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.
The dishwasher runs quieter and the dishes come out clean now.
Well disassembly was good - removed the spring cam assembly on the dump valve cam, then two screws of the solenoid to remove the solenoid, beyond that the repair became a little tough since the seal / shaft retainer wasdifficult to remove. The shaft has a grove which the retainer clip is hard to remove from, and once removed - it deformed, so i installed the seal using a nut driver as a seal press to evenly press it into place. then had to work the retainer with a small set of pliers to reshape it, then reaasembled in place which is when i realized why it was hard to get off due to the shaft grove, which as well as holds the seal it also aligns the shaft latteraly in the pump housing, but after putting it all together and firing up the dishwasher, no leaks and it was an hour laying on my side which i feel was worth it, thx jon
Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.
Pulled the dishwasher out and turned on its back and pulled out the seal. Saw it was bad and order one. It was here in two days and fixed that afternoon. Great service and quick delivery!!! Will use this site again!!
followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.
Had to pull off the front cover where my problem was. Discovered a burnt out switch of some sort, looked it up on your site and found the part. It seemed expensive so I searched a few more sites and discovered you had the cheapest price. I ordered the part on Monday morning and used the cheapest shipping. 5 to 7 days is what i was informed of so i figured it was worth the wait. I got home from work Tuesday and the part was at my door (wow!) I still had my dishwasher torn apart so I put the new part in and about ten minutes later I was washing a load of dishes! I would refer partselect.com to anyone. Thank you! I hope I never need to use your site again but if I do I've got it saved in my computer! (-: