40147 LG Washer - Instructions

Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)

First I turned off the hot and cold water supply and removed the water lines from the back of the machine. I then unscrewed the 2 phillips head screws on the back of the washer for the cover. I slid the cover back and lifted it off the machine. Next, I unscrewed the mounting screws from each inlet valve assemble located on the back of the machine by the hose connections. I used pliers to pull the hose clamps back from the inlet valve, 1 at a time, then reconnected each hose and clamp on the new inlet valve. Once each hose was connected to the new inlet valve, I discarded the old inlet valves. I then re-attached each inlet valve. I placed the cover back on the machine and secured with the 2 screws, re-attached the water supply hoses to the hot and cold side and turned the hot and cold water supply back on. Everything successful, no leaks, and washing laundry again..........leak free!

Disconnected power. Removed washer top; only 2 screws in back. Disconnected two wire connectors on Filter Assembly Circuit. Removed assembly; 1 screw. Installed new assembly, reconnected wires, and replaced washer top.

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.

Basic skill

I ran the spin & drain cycle to empty the drum,I waited to be see how long it took to see a noticeable level of water in the drum (1-2hrs).decided to check the cold water valve first.Found that there was rust forming around the solnoid piston,making it hang up,most of the time it tryed to open, or close. cleaned with light sand paper(piston), and ordered part with parts select. Which was real easy,because of the knowledgeable staff,parts came in as promised,and in good shape,and most important of all it was the exact replacement part. My wife is HAPPY,which makes my life good too! THANKS Parts select..

Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.

remove the front part of the machine to get to the door hinge.

After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the bottom left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

the best video was on you tube and showed exactly how to repair my washer. the parts arrived quickly and was a perfect match. thanks for helping me save some moola and making mama happy.

I took the back panel off the washer and located where the leak was coming from. It was obviously coming from around where the cold water hose connects. Checked washers in hoses and they were good. Noticed a small drip on the valve assembly that the hose connects too. Took off small panel where the hose connections are mounted....disconnected all 3 black water hoses that connect to it (squeeze metal clamps with pliers and slide hoses off. and numbered them with permanent marker so I wouldn't get my lines crossed later), removed the quick disconnect electrical lines.... removed part and googled the parts diagram on this site.....identified the part in the pic and ordered....it was here in less than 48 hrs with the basic shipping (which stated 3-5 days:)....reassembled the same way I took it apart. I'm prud of myself, it was pretty easy and I'm sure it saved me a lot of money!:)l

Followed the instructions that a fellow DIYer posted in PartSelect and a few I watched on Youtube. Pull out the detergent drawer, remove the back screws, slide the top off, unclip the control board, unplug Power & One more switch so that I could move it aside. Take the gasket retention wire off the door gasket & tuck it inside. Remove the screws in the bottom & top. Then slide the front panel, including the door up (not easy) and out. The part received was only the pump motor so I had to take a few pictures before so I knew I got it together right. Remove drain houses, pump screws, slide pump back and remove pump. A few more screws to remove the pump from the housing & replace with new pump. Put it all back together. It works! It only took about 45 minutes

ordered part from Part Select and it was here very quickly,but the part came damaged (not the fault of Part Select). I ordered another one and PartSelect had it here the next day. I watched the video on how to replace it and it was very helpfull.The particular part I replaced (pump motor) does not seem very durable. I will buy an American made washer the next time I need one. I will use Partselect in the future and recomend it to others.