3XWED5705SW3 Whirlpool Dryer - Instructions

Ezee pezee lemon squeezee.

Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!

Unplug the machine. Take off back panel and remove heater assembly. Since I was already into the heating system, I replaced the heating element as well ($30). I replaced the old thermal cut off and overtemp, put the wires back on the connectors, reassembled, and the dryer works like it did when brand new! Within 30 minutes the repair was completed. Still saving for a new front loader washer/dryer, so the repair will hold us until we have enough to buy new. Alos, helped us to need to dry clothes on a clothes rack in the house. Good practice and lesson for the entire family!

I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of drawers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.

Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.

The repair was no problem. Just taking off the hex screws removing the crimp wire and replace the parts in the kit and the old dryer came back to life again.

Thanks

all that was required was to push the catch into the slot notools needed.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

the igniter worked so replaced the two coils on the burner, did not help, read the diagram that came with the machine and replace the high limit cut out. that did it, however the mounting bracket needed to be modified by grinding a tab off, so that the cut off switch would fit in to the bracket.

I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.

Our dryer produced no heat. I thought that it was the electrical heating element because this part had failed a number of years ago. But when we received the heating element, and I opened up the back of the dryer to install it, I found that the element was OK. (Visual inspection as well as using an ohm meter.) I then ordered the thermal cut-off kit, (which was over a week in getting to us because Fed-Ex misdirected the shipment). Once the kit arrived it was very simple to remove the Allen-head screws on both parts, install the two new parts, reconnect the wires, replace the back panel on the dryer and hook up power and the dryer vent hose. The dryer works just fine.

Tested the two thermostats, thermal fuse and the hi limit cut off for conductivity. The hi limit tested open. The others tested closed. Replaced the hi limit. Cleaned lint from the lint duct assembly after removing the two hex head screws that hold the assembly to the blower housing. The lint was packed in there solid. Cleaned up all around. Reassembled everything. Looks and works like brand new. Access was completely from the front panel. CAUTION: The rear panel is spot welded on although it has eight or nine hex head screws also, and when you remove them, the holes don't line up for replacing them. Took a lot of head scratching and time to get things lined up so the screws would go back in again. Don't try to remove the rear panel like the video shows.

Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.