3XWED5705SW2 Whirlpool Dryer - Instructions

very easy

Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed front panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)

I removed the base cover and cover over my lint blower. The thermal fuse is located on top of the blower housing. I removed the thermal fuse utilizing a small nutdriver and installed the new fuse.

I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.

I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace them all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.

You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.

Replaced 4 wheels and new belt

sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.

I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in the country. Thanks for having a web site that is so easy to use and full of good information.

The repair went well, using the whirlpool repair manual and looking at the video from PartSelect. The machine was a bit different than the one in both the video and the manual but that did not cause any problems. The only tricky part was to reinstall the belt "blind" behind the motor, easy to pinch your fingers and also get scratched by the sheet metal edges. To make it easier for that part I supported the drum with the old belt and a bungee cord to the garage frame so I did not have to hold it up and work under it at the same time. When the drum and new belt were in place I just cut the old belt, it was going to the trash anyway.. I replaced the belt and the tension pulley, witch was not turning easy and worn by the belt. I also put some grease ( SUPER-LUBE, www.super-lube.com) on all pulleys. It took about 2 hours because I am 78 years old and have heart problems.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

the igniter worked so replaced the two coils on the burner, did not help, read the diagram that came with the machine and replace the high limit cut out. that did it, however the mounting bracket needed to be modified by grinding a tab off, so that the cut off switch would fit in to the bracket.

Unplug the machine. Take off back panel and remove heater assembly. Since I was already into the heating system, I replaced the heating element as well ($30). I replaced the old thermal cut off and overtemp, put the wires back on the connectors, reassembled, and the dryer works like it did when brand new! Within 30 minutes the repair was completed. Still saving for a new front loader washer/dryer, so the repair will hold us until we have enough to buy new. Alos, helped us to need to dry clothes on a clothes rack in the house. Good practice and lesson for the entire family!

Removed Back and found schematic. Found fuses on schamatic and parts inside dryer. Checked fuses and thermal fuses with an ohm meter and found one that was open. Went to Parts select and ordered part. Relpaced the part and dryer works like new.

My dryer would not start or turn. I first moved the timer to midway between start and end of a cycle and could hear the timer ticking, likely eliminating the timer as the culprit. I next opened the door, manually pressed the door-closure switch and pressed START to see if the heating coil was heating without the drum turning to see if it might be a motor issue. After no heat, I unplugged the dryer and removed the vent hose by loosening the clamp and then removed the lower back cover using a socket and ratchet. Using a multimeter, I quickly found an open thermal fuse. I tested the remaining components to see if they also required replacement (coil, thermostat, high temp sensor) - all tested good. Took a chance and ordered the fuse alone instead of also purchasing replacement thermostat as many advise - if you have not replaced in a while, probably worth doing now. I have replaced mine within a year or two and chalked up the issue to my kids not clearing the vent, so I went without the new thermostat. Model number was found by opening the lid - parts arrived incredibly fast especially for being around the holidays. Replaced the fuse with ease - there is a notch in one end that holds the non-screw end in place so it's flush. Plugged the dryer back in, selected a cycle and confirmed the dryer started and heated as normal. I then had my son open the dryer door to confirm the drum stopped turning. HERE'S WHERE IT TAKES A TWIST: When the door was open, the heating coil continued to glow red hot (faulty timer??) I moved selector to end of cycle and the glow stopped. (timer's good) I then moved the selector mid-way between cycles with the dryer door open and WITHOUT PRESSING START and the coil again glowed red. Disconnected power, disconnected coil and using multimeter, checked from coil input to case ground (any bare metal) and found one side of the coil to be grounded. I was able to removed the heating coil and locate where the coil was touching the case. I shifted the coil back into place, checked with meter (no ground this time), reinstalled and tested with no problems. Reinstalled the back plate and vent hose. Finally, had conversation with the kiddos about being gentle when moving the dryer and all was well. The thermal fuse portion took 15 minutes from diagnosis to replacement. The overall process (due to the additional grounded heating coil) took 30-60. With any repair like this, I usually recommend visually verifying the heat cycles on and off by carefully running with the door open and holding the switch. This will help you determine if you may have an additional faulty part that made the first one fail. (Most likely, thermostat).