3XART718F01 Whirlpool Refrigerator - Instructions

the repair it good and easy ,vo helper to do it.

Ordered new drawer. New drawer seems to be better than factory drawer (slightly thicker). Removed old, removed white handle from old (ran hot water over old to make it less prone to cracking when prying off), pushed old white handle onto new drawer, inserted new drawer, done. New drawer is great; better construction. Thanks.

1.Slid out old cracked drawers 2.Slid in new crisper drawers Simple! It took longer to open the shipping boxes than to install the new drawers! Problem solved! If only all fixes were this easy!!

I removed the screws on top of the refrigerator and the freezer door, lifted the fresh food door off bottom hinge laid it on a covered floor, used a pair of wire cutters to cut old gasket. then pulled the gasket straight out all the way around. then I started on one corner using a putty knife to push the new gasket under plastic trim, then put gasket on opposite corner at top of door then did the same with other two corners, then used putty knife to go all the way around sliding gasket under trim. was easy.

Ordered new set and installed

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

ordered the part by model number of the appliance. Part Select has all the diagrams of the parts you need, very easy to identify and order. Received the part promptly took it out of the package and inserted it where it belonged. Thank you Part Select for your expertise.Dan

All I had to do was snap the end caps into the shelf holder and snap into the door. Easy as can be!

Viewed the viedo - it showed what to do

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

just poped it in

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

I was able to replace the the shelf bars with no difficulty after finding the right parts on PartSelect. The easy to view measuring menu helped me get the right size for the fit I needed. You always worry when you don't have the item in front of you but they make it easy to gauge. I will use them again. I replaced three bars that had been driving me crazy.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

lift glass from shelf. Insert back end of bracket first and snap the front in place. Install both drawers and replace glass and insert both drawers