3KART700GW02 Whirlpool Refrigerator - Instructions

Fridge/freezer warm. After unpluging and plug in again, both would get cold. Then, ice would partially melt in the freezer only to refreeze later. Noted large temperature swings in freezer-up to 48 degrees during defrost cycle. Finally after a day or two, both sides warming up permanently to room temp. Tapping inside the fridge near the cold control (thermostat) would cause the warm fridge/freezer to cool again. Installation is simple. Remove knobs and snap on face plate in front top of fridge. Remove screws allowing plastic cover to drop down which houses the thermostat at the inside top of fridge. loosen two mounting hex head screws from thermostat mount. Remove two plastic covers concealing thermostat wire that travels to vent at back of fridge. Remove thermostat. remove plastic tube over wire on old thermostat by slipping it forward and slide tube on to new thermostat wire. Install is the same in reverse. A thermometer in the freezer confirms very little temperature variation after install (3-4degrees); ice no longer melts, unit stays on!

I watched the repair video and did exactly as described. Excellent video and step by step instructions. Follow them and you cannot go wrong.

It was a drawer I removed the old one and slid the new one in. Took longer to fill out this form than to replace the drawer

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!

Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".

Very simple fix, remove 3 screws, two connectors to the old switch

Placed tray on lower part of refrigerator.

Followed the video instructions.

It's as easy as it can be, but the parts are not the right ones.