3ECKMF8 Whirlpool Ice Maker - Instructions

After removing the ice maker, I guessed that the moter could be the problem,bought new part I installed it and held my breath.thankfully that was it.thanks to parts select I saved a lot of money doing it myself.

It took both me and my wife! One of the new parts we recieved was broke so we took the part off of the one that didn't work.

Unplug the fridge. Used the screw driver to remove the motor. Easy. Now putting the new one in was difficult because it has to line up exactly.
Thats what took 15 minutes but after me and my wife worked on it, we had a bucket of ice by morning!
We only knew how to do what we did because of reading these messages on this site. It came with no directions.

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

Removed the two screws holding the funnel in place...removed the old one and replaced it witht he new tubing...screwed screws back in and the jov was complete. It actually took longer to get it out of the sack than it did to put it together

My husband is a plumber...but did not have time to make the repair. So I took it upon myself!

Super Easy!

1. Unplugged Fridge
2. Unscrewed the 3 screws on motor
3. Pulled out old motor
3. Had to pour some hot water to melt ice cubes that were currently in the shoot. (because the new part would not line up correctly because of the frozen cubes inside the maker). Then soaked up all the water with towels.
4. Inserted the new motor
5. Put 3 screws back in.

ICE, ICE BABY! Within a couple hours it was dropping ice into the bucket! Husband came home, and I told him I fixed the ice maker (his expression was of dread)...and then he checked it out and all was perfect! So proud!

I unpacked the motor and looked at how it was supposed to go in. I removed on screw in the right rear of the ice maker. Pushed a tab on the left of the ice maker. Removed the entire assembly and unhooked the electrical part of the ice make. unscrewed the three screws holding the motor in place and replaced the motor. Put everything in back together and in 15 minutes the familar sound of the ice maker could be heard.

Watched a video on YouTube on how to replace the icemaker control assembly. The video showed unplugging power, turning off the water supply, and removing the entire ice maker from the freezer. After watching the video several times, I unplugged the refrigerator but did not turn off the water supply. I did not remover the entire ice maker from the freezer, but I did remove the wire shut-off arm. After that, I pried off front cover of the control assembly. The control assembly is held in place by 3 Phillips screws; I removed the screws, removed the icemaker control assembly, replaced the assembly with the new one, replace the cover and wire shut-off arm, and plugged the refrigerator back into the wall. Had ice in about an hour (seemed the system had a little delay before deciding to go to work!).

Followed video lnstructions which were very good. Have used your web site in the past and will continue to purchase products. Thanks.

remove the wiring cover, pulled out the ice maker shelf, unpluged the wiring. Once out I removed the control module cover and remove 3 screws and pulled out the old control module. I pushed on the new control module and reattached the 3 screws, attached the module cover and plugged wiring in, slide back into the freezer track, installed wiring cover and screw- 15 minuits tops

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).

Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

sears wanted $450 to replace ice maker or $400 for refubished. I ordered a $60 motor/control unit from parts select. Remove ice maker, remove motor cover, three screws replace and ice within the hour.

Simply removed the old and replaced with the new part.

First I replaced the thermostat. (from this company.) Same thing happened. Then I thought the ice heater has too low voltage and does not melt it for extraction. So, I put a short on the relay on the beam receiver board. No difference. Then completely disassembled the ice maker, and discovered the shaft cracked on the plastic gear, which rotates the ice extractor. So, I ordered and received this control assembly. Put together the unit and having ice again. Due to the cracked gear the thing was out of timing. This gear drives the contactor for letting water in, freezing time, heating the ice, (so it slides out easily), etc

I followed the simple steps outlines in the great video! Thanks