Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 3DWTW4740YQ0

3DWTW4740YQ0 Whirlpool Washer - Overview

Get Parts and Repair Help for 3DWTW4740YQ0

If you know the washer repair part you need, you can browse the list of all parts on the 3DWTW4740YQ0, or you can search by name or part description. You can also find your part by where it is located on the 3DWTW4740YQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 3DWTW4740YQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for 3DWTW4740YQ0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.96

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$61.59

Suspension Rod Kit

This kit includes 4 suspension rods.

$32.23

Clutch Assembly

$24.96

Strike

$9.76

INLET HOSE

This hose can handle hot or cold water and is five feet long.

$2.96

Lid Hinge Mounting Screw

Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.

$5.59

Washer

This part goes on the agitator retaining bolt.

$4.89

D-Shaped Knob Insert

This insert is sold individually. Knob not included. Knob is sold separately.

$12.10

Drive Block - 2 5/16" High

This part is for large capacity belt drive and direct drive appliances.

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Violent shacking in spin mode.

  • Customer: Terry from Homosassa, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable)
  • 88 of 110 people found this instruction helpful
Watched a video on the internet. read more

Scratches in Surface

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 24 of 33 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great. read more

Washer was off balance during spin cycle. The suspension piece broken.

  • Customer: Joseph from PERKINS, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
Replaced 1 of 4 of the suspension bushing. Works great. read more