38JA-2CW Magic Chef Range - Instructions

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML

Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

Range is a 1967 model Maytag. First I removed drawer under oven, unplugged the range and pulled it out from the wall. Removed oven door by positioning it in the partly-open detent position, then pulled up to remove the door. Next I removed 7 screws per side panel: 3 in front and 3 in back, and one on top under cooktop, which retains the cooktop hold-down clip. With side panels removed, I noted the oven door spring position on the intact left side, then replaced the right-side spring first using the same spring adjustment positions. As I replaced the spring, I applied lithium grease to the spring hook pivot points as well as the spring coils where they rub against the interior wall. I repeated the process on the left side. I reassembled the side panels, oiled the door hinges and reinstalled the oven door. Reinstalled range and bottom drawer. The oven door operates like new, and the new springs are totally quiet — good for another 47 years!

After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.

burner was shorting out replaced part works great

plugged it in to the spot where missing element was.

Unplug stove from outlet!! Removed screws (Phillips head) from prior element and pulled out enough to slip of the red and white wires. Keep in mind which side which is on and take old element out of oven. Put new element in and attach wires back on the same sides. Push back in and use screwdriver (Phillips head) to lift insulation to push wires and element prongs back. Put screws back in, close oven door and plug stove back in. Tested and works great!

Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with normal tools.Thanks

1. Removed racks 2. Removed two screws holding in the bake element. 3. Gently pulled out the element exposing the two wires connected to it. 4. The two wires were held by a clip connection. 5. Removed the wire clips holding the wires. 6. Attached the clips to the new element and re-installed the element. New problem: The element did not heat up. A repairman informed me that the selector switch was damaged during the burnout- that switch was no longer manufactured and was discontinued. Whirlpool company was checked and indicated that there was a new part # 7403P023-60 but that was discontinued too. I was able to get the element working by moving the selector switch to the "Bake" position and then moving the switch about 1/4" in the clockwise direction. The element heated and the oven works at least for now as I search for a replacement part. PartSelect was an invaluable aid and helpful all along the process.

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

I had determined that the the burner itself was no longer capable of connecting because when I removed another burner and inserted it, it worked just fine. Also, the defective burner had not worked when inserted into another outlet. I was delighted to be able to purchase a replacement so quickly and easily on my own, without having to call a repair person or seek a retail outlet.

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!