3523WRV Magic Chef Range - Instructions

Called repairman, he never called back for a week. Gave up and found your website, ordered the part. You said it would take 3-5 business days. You lied, it was there the next day. Taking old element out starts with shutting off the juice. Remove trays, pans, etc. Unscrew two screws, pull out elements ends, unclip from wires, reverse the process with new one. You need a light to do this.

removed drawer from track replaced supports on track and one on the drawer.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires reverse the order to install the socet was easy but after i was done discovered that the base of the old bulb was stuck in the socet keeped it for future use

Broken part was already removed, so I used the screw from the broken support and installed the new support. Very simple, easy, and painless.

the new elements were super easy to replace. the old ones just pulled out and the new ones easily pushed in. the top one was a little more difficult only because it had brackets that had to be slid of and then slid onto the new one.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

It would've been so much easier if replacement instructions were included. Replacement screws would've been nice also

Turned off the breaker to the stove. Removed the screws holding the old parts in and unplugged the element. After reshaping the element because it got damaged in shipping I plugged the wires to the new element, replaced the screws and turned the breaker back on. Tried the stove and it has worked fine since.

Unscrewed 2 holding brackets. Removed old element. Unfortunately one clip broke off the wire and had to be replaced. Attached clips to element and replaced holding brackets.
Job is simple but working in the oven without damaging the oven door requires a younger back.
Without problems should take ten minutes.

First I turned OFF the elect power to the stove.
Then I got a flash light to see into the oven. removed the two screws, anf pulled the element out far enough to disconnect the two wires.
Put the connecters on the new element pushed it back put the two screws back.
Turned the power on works great, very easy.

Repair went fine as I read on how to do it and it worked fine. Hardest part was hitting the hole for the screws.

#1...love the website where it helped us diagnose our problem. Also the video where it showed us exactly where and what to do. #2 we accessed the rear of range and unplugged. #3 Took back panel off of range to exposed wires and clips of heating bake element. #4- removed old element from the clips to find that one end was FRIED and FRAYED. Like something burned through the clip. 5- We cut and stripped the end of the hot wire, re-attached the new clip to repaired wire. 6 - plugged her back in...turn the oven on to see that the NEw coil heated up wonderfully. BEST part of the story yet....I placed the order via internet on Monday at 3:45 pm. I paid for the standard shipping of $7.95 or 3-7 day delivery. On Tuesday AM....the very next day, I was WOKEN up by my doorbell at 8:05 AM....by the time I got to the door to see who it was...the FED EX truck was pulling out of my driveway. THEREFORE I got overnight delivery without paying for it. AWESOME delivery, service, transaction....and great website and parts!! HIGHLY recommend to all!!!!

Repair is really easy. Just remove two screws, pull ( gently ) on the bake element until you see the electrical connectors. Remove and do the reverse with the new part. Oven works just fine.
Really Really easy....

Removed two screws and unpluged old element plugged in new element and re-attacheched to oven. No Problems at all.

Shut off electricity to appliance then unpluged wiring from old element and pluged in new element.