3187VTA Magic Chef Range - Instructions

removed cover over burner section ,removed power to burner section ,removed burner assembly, replaced ignitor assembly, wire in to control circuit ,replace burner section in oven,turnon power chech operation ,replace cover.

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

Removed door, took off old igniter. Had to redo plug , simple, because kit had wires to splice to make it work. Whole job was 30 min. Recomend to anyone. Saved $75 on a service call. Bill

removed inside trays and grill inside large oven door on front to get to ignitor,removed ignitor with 1/4 drive socket,followed the wires off the ignitor thru the hole in back of oven and disconnected the connector,put on in reverse order.To simple to even write about,anyone can look at it and tell what needs to be done

Remove old igniter ,,again had to remove rear panel of unit to get to connecter..reverse procedure to install igniter. Video very helpful.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.

really easy thank you to your video

was very easy did just as the video showed how to do

quarter turn with hand to remove old head...removed two wire leads attached to head to reattach to the new head...each wire fitting is different so you can't mess up...put on new burner head..quater turn to tighten...done...thanks...

removed the top plates, the burner heads and their ignition wires. removed the four screws from the range top that hold the gas orifices to the top.Lifted the top off of the stove. used a 1/2 inch open end wrench to remove orifice tube assemblies. put the new tube assemblies in place, wrenched them down, secure but not overly secure. replaced other materials in the same way the they were removed. it took about thirty minutes. had some difficulty replacing the stove top.the stove is an older model and some of the pieces moved when the top was removed.

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

The hardest part was removing the burners themselves, I used an oil filter wrench to twist them off. After that it went pretty quick. I also used a toothpick to clean out the holes on the burner, and now the igniters work on all the burners.