3167XYW Magic Chef Range - Instructions

The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping the new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.

I didn't. Don't know how to get to light bulb to change it for this specific model

First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

Removed old seal parts and had to cut new part to put into space but it went in without difficulty and has sealed the stove door tight again.

moved stove away from the wall, Disconnected power, Removed 2 screws on the access panel and removed panel. Disconnected qwick release conections on heat sensor and ignitor, Removed oven door and burner cover to expose ignitor, removed 2 screws to remove ignitor and replaced ignitor. Removed 2 screws and removed sensor, replaced sensor. Reconnected qwick conects on sensor and ignitor. Replaced oven door, burner cover and access panel and checked out. Checks OK !

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

So simple! I really had no idea what the problem was. I found the PartsSelect site, read the comments from fellow Maytag double oven owners, diagnosed the problem as the sensor and ordered the part. It arrived in only two days! We removed the back of the stove, pulled the old sensor through, plugged the new one in and YAY the oven is like new. I have to admit most of the repair time involved sweeping up the dog hair that had accumulated under the stove.

slide out stove remove rear cover (6 screws) to access sensor plug . remove two screws from inside oven area and remove part,replace in reverse order.

Unplugged the stove and unscrew the 2 screws on the thermometer inside the stove and unplugged the white plastic in the back of the stove and I had to put the new extra piece that came with the sensor kit as it was needed because the socket were different.

ordered wrong part, called, was sent return number, sent part back, account credited ... easy return policy ... friendly people, good job

The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

1. Screw the burners counterclockwise 45 degrees to remove each burner. Some gave easily while others were baked on.
2. Remove one philips-head screw per burner.
3. disconnect ignition wire from each burner.
4. remove stovetop.
5. remove the previous hammered orifice and tube assembly by unscrewing 4 nuts.
6. attach the new assembly and follow steps 1-4 in reverse order.

I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.

Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. So I just rested the new one on the old plate.

Pulled each wire slowly out and inserted it onto the new spark module.

Screwed in all the panels back and returned the stove to its proper place.

The range now works as well as the oven, but my broiler still does not light up.