31315XBA Magic Chef Range - Instructions

Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

Followed the directions on the video. Very easy to do.

The burner head caps on my Magic Chef no longer work and had to be replaced. I ordered 1 of the 4 caps to see how it would work out for me. I did not have any issues replace the cap. I contacted PartSelect and order the other 3 caps. The sales representative took my order and was EXTREMELY helpful. Now I know why all of my neighbors choose PartSelect. Including the cleaning, it did not take me more than 15 minutes. The video was also extremely helpful. Our Magic Chef should be good for another 6-8 years. Thanks PartSelect.

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

turn burner cap counter clock wise lift out remove to leads,do not have to turn power off they are mini volts.Insert the two (leads)weirs on to new cap,twist back in done.Fire it up.

I have and in the wall Magic Chef oven CGW3330ADW seriel 10799876US that came the purchase of my home 10yrs. ago. After a black out and 2 brown outs my oven would not start and the F3 code is beeping and the "door lock" light was on but the door was unlocked. The clock was working fine, but could not use the timer or set the temperature. I googled "FLASHING F3 code" and one of the results was the comment thread on the Parts Select website. When I clicked the link I read several customers sharing their story that was very similar to mine. I was able to click on a video and see a short demonstration on "HOW EASY" it was to replace the "Short Oven Sensor Kit." I though, "Yea right!" I left a comment on that You Tube video with my make and model and a brief explanation of my problem. I received a reply to my comment with in 24 hours, confirming what other consumers had shared...The "Short Oven Sensor Kit" was needing to be replaced. I ordered the part for around $30 VERY late on Thursday evening and when I woke on Friday morning, I a shipping confirmation email. I received it VERY early on Saturday morning! I was able to replace the part very easily with in about 10 minutes. I was VERY LUCKY that I was able to to the repair WITHOUT having to remove the oven for the wall! I would have had to pay for help if I had to remove it from the wall. The Parts Select web site save me over $400 which was the estimate for the parts and labor from a local appliance repair business! I was told that it would probably be cheaper or about the same as buying a new over which was their recommendation. I am so glad that I decided to do the research and in less that 1 hour I had my order placed. Thank You Parts Select!

quarter turn with hand to remove old head...removed two wire leads attached to head to reattach to the new head...each wire fitting is different so you can't mess up...put on new burner head..quater turn to tighten...done...thanks...

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

Watch the video, it's too easy and best of all, the part fixed the oven!