Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Igniter was not getting hot enough to allow burner to come on.
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,
All I needed was a phillips screwdriver to take two screws out of the top panel. Then the two side panels pop off. Notice there are three click tabs on each side panel, and also that the top and bottom of the left and right panels, must be manipulated in a sliding action(front to rear facing the oven door front.) A good deal of hand force is need to accomplish this. Clean the old glass out, put the new glass in, carefully might I add, and reverse the above process. Just a little mechanical inclination will get you there. Good luck! I almost forgot to add that this job goes a lot easier if before all of this, you simply remove the oven door from the oven, by opening the door about ten inches to the point where it stands open on its own, then grasping it firmly on both sides and pulling up, with a slight jerking action. This breaks it loose so it can very very easily be removed, and replaced. Best of luck!
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!
broke the igniter in the oven before I even got the oven installed
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.
Oven would not start, ignitor was not doing anything
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.
1960's oven door gasket fell apart, actual gasket not available any more
Chose rubber flexible gasket with metal tabs. cut to size. unscrewed metal bracket on inside oven edge on 3 sides, slipped metal tabs between oven and metal and screwed back in. Done! Not a perfect fit but pretty good - better than no gasket.
First remove the burner head by turning counter clockwise to unlock. Use pier to remove the wires from the igniter and burner. Once both burners heads are removed from 1 side, use screwdriver to remove both screws that is holding the burner orifice fitting assembly. You want to repeat the process for the other side. Once both sides are done, you can lift the range cover to gain access to the broken burner orifice fitting assembly. Use adjustable wrench to unscrew the two nuts that are holding the assembly in. Remove assembly and replace with new. Reverse the disassembly process then you are done.
All identification of the stove was missing, other than the brand name on the exterior of the top of the range. Tried to match the knob to one found on the Part Select site. Found one that matched the appearance and ordered it. Found out that when it arrived it was 180 degrees off when installed on the thermostat shaft. Not the fault of Parts Select. Called customer service and they were unable to track anything from the part number cast into the back of the knob on the range. Suggested I try the Whirpool customer service line, and arranged to have the knob I purchased returned.
I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.