25370503413 Kenmore Refrigerator - Instructions

Rack door slid into place easily. Repair required no tools and took maybe 20 seconds to install!
Very easy job!

My 4 year old grandson used the frig door as a swing.The bottom hinge cracked, then the door wouldn't seal. I propped the door up with some books, removed the broken hinge (2 bolts) and replaced with the new part. Simple fix on the door, only time will fix the 4 year old!

YOU TUBE VIDEO POINTED ME IN THE RIGHT DIRECTION. USED MULTI METER TO CHECK FOR VOLTAGE. NONE, REPLACED DEFROST HEATER. WORKS LIKE A CHARM, PART DELIVERED TO MY DOOR FOR LESS THAN $60.00, IN TWO DAYS FROM PARTSELECT. FIXED IT MYSELF FOR LESS THAN THE COST OF A SERVICE CALL.

Pulled the refrigerator out from the wall. Then unplugged it took my nutdriver with a1/4" socket on it and took out the screws from the cardboard back on the bottom of the refrigerator. Then I removed the two screws holding the water valve on. Then I unscrewed the supply water line from the main water inlet valve. Then I removed the outlet waterline going to the ice maker from the water valve. Then I reversed the procedure to put it back together. Hooked up the main water line and turned the water valve on for the water to flow to the valve at first nothing happened had to wait for a couple of hours for everything else to get to the right temperature before the ice maker would start making ice.

Pull refrigerator from wall and disconnect the water line and unplug the power.

On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.

Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..

Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.

Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.

In about an hour you should have ice filling the bin. Enjoy!

Used model # of frigidaire on your web site... reviewed parts available... noticed shelves abailable... zoomed in to measure using crosshatch background... measured my freezer compartment... seemed doable... ordered shelf... receivednext day... attempted to slip in slots... had to grind off 3/16th inch on two legs... slipped in... Perfect!

I removed the back cover and removed the clip holding the compressor- run capacitor and start relay. I replaced these 2 components and clean the dust from the frig., and from the bottom of the floor. I replaced the back cover ; Loss about $300 worth of meat when when the frig. failed. Then I thought that, during these turbulent times, there are many which don't have a refrigerator or any meat to place in it, The refrigerator is "running" normal again.

We took off the broken bar and put on the new one. It clips on. Took about 10 seconds and could have been done by a 5 year old.

Snapped in the bars and with the seal once on the track went right on

Just removed the broken pan and installed the new one within 2 minutes. Really simple

Watched YouTube video. Very easy. Used my cell phone camera in ‘selfie’ mode propped up in the upper right hand corner of freezer to see the 2 hidden screws.

Took off old part and installed new part

just slipped the part in place

Removed bars from doors snapped in new replacements

I ordered a freezer gasket/insulation lining; just pulled the old one out and put in pressed in the new one; solved the problem easily. Then the refrigerator gasket was falling apart. I was ready to buy a new refrigerator but then I got laid off from work. I ordered the 2nd gasket. It did not fit easily at all. My husband had to man-handle and stretch it; then it worked, as worked well ever since. Spent $250 instead of $1250+. Thanks. P.S. Could not find the year of the frig.