2426*1A Roper Range - Instructions

First I removed the screw that held it in place with a socket. The agitator became loose and easy to remove at this time so I lifted it from the washing machine. I then just placed the new agitator in place and replaced the screw being careful not to do it too tight. The replacing of this part was an easy job and thanks to Part Select it saves me hundreds of dollars.

unplugged unit,removed liquid cup,removed nut holding agitator,removed agitator installed new one installed nut tightened and tested operation very easy job!

pulled the detergent cup off, pulled the cap out of the upper part of agitator, removed bolt and pulled assembly out. then reversed the process with the new assembly.

Installation of my new agitator was a cinch. After removing the top softener dispenser and bolt cover, I used a socket wrench and extension where I then removed the 7/16ths bolt that holds the agitator on. After lifting out the old unit out, I simply positioned the new cam with dogs into the new unit...snapped the top part of agitator onto the bottom section...placed the new unit into place inside the drum, re-tightened the 7/16ths bolt, placed the new cover into place, followed by the softener dispenser. The entire process from start to finish took less than 15 minutes thanks to the easy and clear to read set of instructions. I saved a bundle doing it myself thanks to this site

The new agitator came within 5 calendar days of ordering, it was sent from near my house.
I looked at the directions sent, and saw that it was very easy.
First I took off the fabric softener dispenser. Then I discovered I needed a socket wrench to take off the bolt holding the agitator on to the driveshaft. So I went and bought a wrench, extension, and socket.
Then I came back and removed the bolt, installed the new agitator, and washed a load of clothes, within 45 minutes.
It worked fine.
It was going to cost me over $150 to have Sears fix it and it would not have been until the following Thursday Sears Applicance Repair could come.
So I spent about $80 for the new agitator from Parts Select , $30 for the socket wrench, which I can reuse. So I saved $40 and a lot of aggravation.
And I got to wash clothes quicker. With 4 school kids we wash a lot of clothes which was what broke the agitator in the first place.
I would recommend Parts Select any time.

removed nut in center (take top piece off and look down), lifted old agitator assembly off, followed directions to assemble new agitator, replaced with new "swirl" designed agitator assembly, replaced & tightened nut with nut driver, and although my old model washer was not listed as "compatible," everything fit and it seems to be working just fine so far. Be sure to cut power off to appliance before starting - just in case.

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

Removed the single screw securing the agitator to the drive shaft. Removed agitator assy. Installed new assy. Reinstalled securing screw.

It was easy to do. You just need a socket set what's a Long Reach In order to get the nut out of the agitator. Other than that piece of cake.

I just removed the old agitator and replaced it with the new one. Took less then 10 minutes. Took one bolt out pulled the old agitator out put the new agitator in and replaced the bolt. So easy anyone could do it. Much cheaper then buying a new washer.

new element plugged into burner connection- an easy fix

so easy, just ordered the part, the part came and inserted the element into the stovetop

Replaced the element. The part came the next day which was great. Good customer service!

Pulled out electric heating element and replaced with new. I have had this frustrating problem for 2 years and after replacing the elements they now work like new! My only question, why did it take me so long to replace???

pulled off cap at the top agitator took out seal used socket to take out bolt in center of agitator pulled old one out put new one in replaced bolt seal and cap at top