20487 - Instructions

Unplugged the washer. Pulled it away from the wall far enough so it would be stable tilted back against the wall. That way I didn't have to disconnect any hoses or lay the machine down.

I used a ViceGrips to squeeze the hose clamps and then pulled the hoses off. Getting the pliers in the right position in the tight space was the hardest part of this whole job, and that still wasn't particularly hard. I have medium sized hands (for a man).

I flipped open the retainer clips with my fingers. Pulled the pump off and slid the new one on. It helped to make sure first that the flat side of the motor shaft was roughly facing the same way as the slot in the pump.

I reattached the hoses and popped the retaining clips back on. Held my breath and ran the washer. No more leak!

Incidentally, before I discovered PartSelect I called Whirlpool service. I asked if they could have the tech show up with the part. They said "No." I'd have to pay the fee for a diagnostic visit and then the tech could order parts and return to install them. They said there would be no service charge for the return visit.

Several years ago I believed this story when I called for a dryer repair. However, when a second technician returned with the part I had told the dispatcher the first time around was needed, he came up with some excuse why there had to be a supplemental service charge. I challenged it on my credit card and eventually got it removed, but it was a hassle.

Thank you PartSelect! And thanks to others who posted their experiences and gave me confidence to fix it myself.

The new pump arrived at my door just a few days after it was shipped.

Once I got the water hoses off and the clips holding the pump I had to use a large screwdriver to get the pump off the motor shaft. I then tried putting the new pump on but it wouldn't fit. I noticed that the motor shaft was flaired out (possibly due to rust) so I used a Dremel Tool with a grinding disk to carefully grind down the shaft to what it looked like it was supposed to be. Once that was done the pump easily slipped into place. I attached the pump clamps and hoses and pushed the washer back into place. I ran a quick test and then later a load of laundry. No more leaks!

I read the trouble shooting guide on your web sight to figure out what the problem was and after checking the hoses the pump seemed the next most likely problem. So I ordered the part.My main problem was the lack of room to work,if I could have tipped it on it's back or raised it I would not of had a problem.But I tipped it up and blocked it from falling and removed the part while waiting for the new one to arrive.Once it arrived it only took a few minutes to install.When I tried the washer it still leaked water,so I tipped it back up to check it out.The only thing that was wrong was that the spring hose clamps had not seated yet so I moved them around and wiggled the hoses to try and get them tighter.The next time ,it worked fine.The other reviews and trouble shooting guide were a great help!

The repair went fine and the U - Tube video was very helpful. However, the putty knife under the front corners to release a spring clip was not accurate to release the console. Our Roper had two philips head screws on each corner of the back of the console that had to be removed to allow the console to slide back and off its clips. Then the housing of the machine (sides and front) was not coming off as described. However, after measuring I determined that the water pump had enough clearance to be removed without the housing of the machine being removed. So, the repair was even simpler than described.

It was the first time I ever ordered parts online or even attempted to repair a washer. You all have made finding and ordering the right part very easy. I got the part in 2 days even though I used the cheapest shipping option (5 to 7 days). I turned off the water, removed the water lines so I could lay the washer on its side. No tools were needed to remove the water pump, just two clips held it on. I put the new pump on, hooked up the water and washed a load that night.

Removed the two spring clamps from hoses; removed hoses from pump. Removed spring clips holding pump to motor. Had to pry pump off of motor shaft due to rust on shaft end. Sandpapered rust off of shaft and then lubed same with oil and new pump slid easily onto motor shaft. Re-snapped spring clips to hold pump onto motor and then reinstalled hoses and their spring clamps. Whala, end of story, job well done.

My husband got the part within 2 days of the order and replaced the leaking pump within a half hour. The repair was very quick and easy for him and your company's prompt delivery prevented my floor from getting wet everytime I did a load of laundry. Thank you and we will continue to get parts from your site in the future--hopefully we won't need to anytime soon. but we know you are there if we need to repair!

Frist I removed the two water hoses going to the pump. Second releaseed the two clips holding the pump , it came right off the motor shaft.
Third, put the new pump on the shaft, put the clips on last the hoses good to go.

First I watched the repair video. Then I pulled the power plug and shut the water off. I didn't have all the room available to remove the front and sides of the machine in my narrow hallway so I just slid it away from the wall and leaned it back against the wall and had plenty of room to do the repair lying on my side. $28.00 part and in 20 minutes all done. This is the second time this site saved me time and mucho money. Thank you. Leon B. from Massachusetts

laid washer on side, used butter knife to pry off spring clips. there is just enough room to get pump off the shaft .Unhook two hoses then install new pump.

plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up

Unfortunately my washer cabinet did not come off as in the video so I had to do repair from underneath. The rest of the repair worked exactly like the video showed. I had a couple of small, sturdy wood boxes about 9" high which I used to brace the washer after tipping it backwards a bit (and unplugging it too). My wife acted as a spotter to be extra safe. The only two things that required the hook tool and mirror were: 1) Working from the bottom my hands were at an awkward angle so I couldn't pop the retainer clips off the pump, but a hook tool (like a screwdriver with a hooked end) popped them off easily, and 2) The other issue was once the new pump was in place I could not locate the slot for the top retainer clip until I could look at it with the telescoping handle mirror, and then I was able to put the clip in by feel. Extremely easy repair, especially with the guidance from the video. Thanks for video help! WH

First unplug washer and turn water off (both hot and cold) You only need to pull washer out away from wall about 1 1/2 feet. Take a putty knife and slide under the front corner of the control panel ( both sides one at a time) lift up corner as you slide putty knife under the corner. After both sides are released on the control panel slide control panel forward( about an inch) to release rear of panel and flip panel over the top. Unplug the lid safety switch then with a screw driver unsnap the cabinet straps one on both sides that were under the control panel. Put screw driver into the spring strap end closest to you and push screw driver back which will release the straps( one on each side). Next tilt the cabinet toward from the back( about 6 ") and lift up about 2 " the cabinet can now be removed. Undue the two hoses on the water pump that is located at the bottom of the washer in the front ( make sure you catch the water from the hoses in a small pan). Undue the two spring clips that hold the pump on. Pull pump straight out (about 1 ") discard old pump and install new one in reverse order. When reinstalling the cabinet there are two stubs on the bottom bracket on the washer that have to put into the slots in the lower front corners of the cabinet ( the hardest part of the whole project is putting the cabinet back on, the trick is what I described above with the slots in the lower front corners. Good luck it very easy to do.

Of course I tried to determine where the leak was from. There wasn't a solid flow of water and was confined to the front. Pulled the washer out and laid it down. Noticed that a metal clip had a little corrosion on it and followed it back to the water pump seal. Removed two hoses and unclipped the pump. That's it. No screws or nuts. Looks like it was expected to fail and was easy to replace. It did last for 20 years though.

Unplugged the washing machine. Removed the two philipps screws holding the control panel. Swung it up , disconnected interlock connector, and pried the two clips. Removed the top and cabinet assembly to have easy access to the leaking pump.
Disconnected the two hoses connected to the pump. Used the plier to loosen the hose clamps. Removed the two retainers securing the pump. Removed the old and damaged pump and replaced with the new one. Reinstalled the retainers back on. Reconnected the hoses and clamps. Put the top and cabinet assembly back on. Snapped back the clips and reconnected the interlock connector. Screwed the control panel assembly to the cabinet. Done. Ran the washing machine to check for leaks. Found none.