2032 - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replaced gasket that go's between the air cleaner housing and carb. cleaned housing and reinstalled with new air filter
Also replaced fuel tank , the built in fuel shut off started leaking , had to replace the tank. Ordered a new one Briggs & Stratton original equipment fit perfect . This is a 25 year old Briggs & Stratton lawn mower 3.5 HP, Runs perfect, starts by the 2nd crank every time. First time I ever had to spend money on it since I bought it new in 1991
Parts Used:
-
Barry from FRANKFORT, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
12 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Smelled Gas Leaks
Inspected/removed fuel lines and found signs of leak. Removed and inspected carburetor and found that seals and gaskets were toast. Replaced said seals with ones from the kit that fit and replaced fuel lines.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together with all the necessary clamps.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together with all the necessary clamps.
Parts Used:
-
Jonathan from LIBERTY TWP, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grandson lost the ignition key to my Toro!
No repair, lol! Just a perfect fit for my ignition :). I bought two in case my grandson gets curious again.
Parts Used:
-
Michelle from AYLETT, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 35 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dull blade
Disconnected spark plug wire laid lawn mower in side removed blade bolt took off old blade put new blade on tightened it reconnected spark plug wire
Parts Used:
![](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/9011577-1-S-Husqvarna-532145106-20-amp-34-Blade.jpg "20" Blade – Part Number: 532145106")
-
Robin from BIRCH RUN, MI
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced cable brake
Everything went very easy and was done in no time. After I put on new part, mower started right up.
Parts Used:
-
Jo from SAINT LOUIS, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My lawn mower blade wouldn’t stay in place. The old blade adapter had worn down and broken.
I took off the old blade adapter and put the new one on. It literally requires removing one bolt. Unfortunately, once I started and ran my mower for a few minutes it blew up and left a charred patch of lawn. The underside of the mower is mangled metal and unusable now. The repair, though, was super easy!
Parts Used:
-
Joel from ROSEVILLE, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
3 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Spring-choke Return was not the right part.
The repair did not happen. The item number PS9294414 was the wrong
part. When I looked up the model number of 126-T02-0625-B1 engine after I tried to install it. The PartSelect answer was that they no longer had parts for 126-T02-0625-B1 engine any more. Do I need to send the
Spring-Choke Return and get my refund back. If so how do I do it.
part. When I looked up the model number of 126-T02-0625-B1 engine after I tried to install it. The PartSelect answer was that they no longer had parts for 126-T02-0625-B1 engine any more. Do I need to send the
Spring-Choke Return and get my refund back. If so how do I do it.
Parts Used:
-
Linda from Louisville, KY
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers
1 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheel height adjuster lever (spring steel) cracked / split in two.
Tip mower onto side, raising side to be repaired. Empty gas tank if possible or use rags to prevent gasoline drips onto clean surfaces.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Remove wheel using a 1/2" socket.
Remove wheel height assembly with 1/2" socket and open end wrench to hold nut below the deck.
Position new spring arm over the slot on wheel height assembly plate. Check opposite side to verify correct orientation if needed.
Remove plastic cover from old lever using a small flat blade screwdriver. Slip onto new lever.
Replace wheel height assembly.
Replace wheel.
Parts Used:
-
Ray from YARDLEY, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set, Wrench set
5 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!