1949 - Instructions

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

I removed the old flange pieces before ordering the new one, then repositioned the washer after attaching the new one to the washer top. I then attached the flange to the counter top resulting in a more stable appliance. It was simple to remove the screws and install the new flange.

I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!

Ours is a portable with butcher top. Three screws under the front edge allow the top to be slid forward and off. Then it is obvious which screws release the old flange.

The latch hook needs to be separated from the metal strip and inserted into the front of the flange through the slot, then secured back onto the metal strip.

Don't tighten it too much until you get the thing back together. Then adjust it so the door closes tightly and make it tight. If that machine screw works loose it allows the latch to move sideways which will widen the slot--not good.

It should be checked for tightness every year unless you want to replace that plastic part again. It should have been made of metal to begin with. I'm surprised Maytag would use plastic in such a part.

Not a difficult repair unless you are a total klutz with a screwdriver.

Removed power, removed the ice maker being held with three screws. Replaced with old unit. This box was so old that I robbed parts from the old and placed them on the new unit. Mkes ice very good.

this is a portable unit
the wood top is removed this allows access to the side cabinet screws and the lower front trim screws behind the lower front trim panel you can access the hose connections disconnect and reinstall
new part works great!

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

Had to loosen the drive motor enough to slip the belt around the pulleys. The only problem was the amount of space available to work in.

Very slowly, had no clue what I was doing. Instructions were great, and even I got the job done.

I did not do the repair yet, there is no schematic on how to route the hose; also no description of how to do the routing/connections.

remove 3 screws from either side door edge trim : Note ! panel "notches" are up : remove both original panals plus the cardboard spacer : swap only the old color with the new one and reinstall spacer cardboard and be sure it stays centered : remember panel notches are up : carfully slide the panels over the spacer cardboard while keeping the cardboard centered : becareful panel edges can scratch in the door trim : Note! opposite side door trim can be removed if needed .

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.

This was very easy and pretty fast to do and its working great...all for $40 bucks ! you can do this...trust me!