All Installation Instructions for General Electric Range 16481-1

Replaced All Burner Receptacles After One Failed And Also Replaced Ball Burner Bowls

This installation was for a replacement for one of the burner bowls on the original order. Replacement bowl fits proiperly.

Parts Used:

Burner Bowl - 8 Inch

ROBERT from MECHANICSBURG, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Trim has tendancy to rust on range oven door

Unscrewed bottom screws, replaced trim. No trouble.

Parts Used:

Bottom Trim - White

Carole from San Diego, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

slot that heating element fits was worn down and caused burners to be uneven

replaced with new ones

Parts Used:

Burner Bowl - 8 Inch

Burner Bowl - 6 Inch

Judith from Broadway, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

bowls were worn out

Open the box and inserted the bowls

Parts Used:

Burner Bowl - 8 Inch

Burner Bowl - 6 Inch

frances from winston salem, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven Door Handle End Caps.

I purchased my stove second hand. It was a mess but I saw a gem under all that dirt and grime. It took me a week and it looked brand new. The end caps on the oven door handle were discolored and cracked. They made the stove look old. It was an easy repair and my stove looks brand new. I will order an extra set just in case as these parts are getting harder and harder to find. I am so pleased with the original parts. They were here with in days and well before promised delivery date.

Parts Used:

Door Handle End Cap

Linda from Lake Panasoffkee, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Replace damaged oven door handle

Required removing the door, by sliding it off the hinges (open 1/4 then lift up), removing the outer frame which releases the inner glass door section exposing the door end screws. Removed the phillips head screw on each door end releasing the old handle. Inserted the new handle in the ends, screws replaced, reversing the above. Thanks for the correct part. Byron C.

Parts Used:

Door Handle

Byron from Fayetteville, GA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Trim part on bottom of door was rusty

I ordered the part, It came a few days later,,Within 15-20 minutes, I had it installed..Pretty easy...Thanks

Parts Used:

Bottom Trim - White

Richard from Euclid, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

The burner bowls were encrusted with grease and spills.

I easily took out the old ones and put in the new ones sent by Part Select. As promised they fit perfectly. Now when my wife cooks there is no more smoke and it does not set off the smoke detector.

Parts Used:

Burner Bowl - 8 Inch

Burner Bowl - 6 Inch

Ed from Canyon City, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Rusted oven door trim

Removed old part by removing the screws at the boottom of the oven door. I wasn't sure if the glass oven door cover would remain in place once the trim piece was removed, fortunately I was ready when it came down. The glass cover is large and heavy so you need to be ready to handle the bulk of this piece once the last screw is removed. Cleaned everything and with the help of my wife, who secured the oven door cover in place, secured the new trim piece by replacing the screws. What a difference, looks like new! PartSelect provided great service in terms of speed and part acciracy.

Parts Used:

Bottom Trim - White