12001747 Maytag Ice Maker - Instructions

Removed all screws on back and 4 on front. That part is easy IF you have a Torx of the right size. Slip out the ice bin a bit and replace the drive ring. Reassembly is a bit harder since some internal shift can occur -- rotate or tilt the whole assembly to get two -- I think -- screws started. No need to over tighten screws; snug is good enough.

Took my husband and son to remove the auger because it seemed to be frozen somewhat. After a little work, the auger broke loose and the repair was a quick process. I thoroughly enjoy the fact that the part was correct and I my ice maker was fixed for very little money and I did not have to buy a new refrigerator! I was not sure that we could get the replacement part because we are not the original owner of the refrigerator. So it has some age, but still works strong!

Removed drive assembly end of ice bin using socket wrench to get to old ice bin drive ring. Pull drive sssembly back to get ice bin ring out of the other end of ice bin. Installed new ice bin ring and and reinstall drive assembly end.

looked a website removed part found broken item order and installed in 15 minutes, easy simple fix very low cost change

rl

My son-in-law is our handyman. He diagnosed the problem, found us the part and then put it in. The part came several days before we expected it and the whole thing went very well and we saved lots of money!

the drive motor was broken free from the tray, so I just changed it over and replaced the drive ring very esay for me

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

Remove 2 screws, and GENTLY remove tray. There are two motors on the back side that are wired in to the back of the fridge. Unplug the harness and the whole assembly will come out. Take note of the way the plunger comes out, if not, it will take a little more time to figure out. reassemble motors onto new tray then GENTLY slide into postion, with one hand plug in wiring harness then seat tray into position and reinstall screws. Done.

To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.

Easy disassemble removing screws to separate front of ice bin.Be sure to note how metal rod is attached to rear of ice bin. Installed drive ring and reattached face (front) of ice bin in about 15 minutes.

Checked the ice tray and could only find the drive ring had some breaks in the plastic. Actually did not see why this would stop the auger from turning and dispensing ice. However this was the only thing I could find wrong with the unit. I pulled the tray, removed 6 screws (star tip heads) pulled the auger forward and replaced the drive wheel, put the unit back together and its been working fine ever since.

removed torx screws and replaced ice bin drive ring.

Easy repair - Don't over complicate it. 1) Flip up ice bar to stop making new ice. 2) Pull out the complete ice bin/tray. 3) shut freezer door while you work on the ice bin. 4) All you need to do is remove the 4 screws holding the ice bin holding tray to the front of the Ice cutting section in the front. 5) Screw drive can then be pulled forward to remove the old/broken white drive cap. Just replace the White Drive ring, put the drive screw back into the ice bin tray and re-install the 4 screws. 6) When re-inserting the bin, you may have to twist the screw drive slightly to re-align with the motor bracket in the back of the freezer. Suggestion: throw out old ice because if it is wet or slightly melted, when you put it back in the freezer the ice will freeze/clump together into a large ice clump; not cubes. Also dry out the ice bin so there is no water to freeze up or create a new jam when the ice bin now re-freezes.

Repair was relatively easy. I found several videos on You Tube on repairing or replacing Solenoid & Ice Maker Auger Motor. They weren't broken but those videos show how to replace them and remove ice enclosure, which was the part broken. Only issue was removing yoke off the motor. It has reverse threads and videos had shown holding shaft of motor with needle nose pliers to hold it while you thread off the yoke. You need good needle nose pliers with teeth on them or the shaft will slip in them. I had to go buy new pair while repairing. It's all goes back together perfectly! I took pictures of the assembly, before I removed everything and needed to refer back to them when I was reconnecting the wires.