1107012511 Kenmore Dryer - Instructions

After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing the belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)

The hardest part was figuring out how to access the dryer mechanism. This Amana dryer has a lower front panel that is removed and not the top. There are few instructions available for this configuration. Then the part locations do not resemble the video instructions for trouble shooting. I discovered the broken part because when fiddling with the wire connections the metal tab disconnected due to fatigue or corrosion. Removing, identifying and replacing the flame sensor was quite simple. The dryer now works as before. The dryer is 23 years old. The most time in this repair was spent figuring out how to disassemble and identify a different configuration than in the videos.

Took dryer apart. Should've started with You tube videos so I took more apart than I needed.

Got all the parts I needed from Parts select.

Fixed it and works great.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.

Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.

Removed the back panel of the dryer. Thermostat is located in the out going air flow near the exhaust. Removed one screw that held thermostat. Exchanged wires and put everything back together

just remove 4 screws removed the drum and put the affected part and that's it

Followed the video and stopped at each part not one issue very easy repair most difficult was separating the electric from from panel a little tricky to get apart.

Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!

replaced rollers, belt and pulley. Video was very helpful

flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.

Removed back cover and replaced thermal cutoff, installed new push on terminals. Bolted back on and dryer is working like new again.

Read this site and saw many fixed the problem with a new thermostat. Ordered one and it was simple to replace. Just removed the back panel of the dryer and the thermostat is right there. Two screws to remove it, swap the four wiring plugs onto the new one, reinstall it. Unfortunately that didn't fix it so went back online and ordered the coil kit, another common solution. Removed front of dryer by removing the two screws the hold the lint trap onto the top and the two hinge plate screws on back of dryer to tilt the top up ward and backward. Removed two mounting screws on inside of dryer front and slip front panel upward to remove. The coils are right in the front down at the bottom left of dryer.Used an offset screwdriver to remove the two screws holding them in place. They slide right out, one has two prongs, one has three. Replace them with the new coils and put them back in place. Reassembled and everything works now. Grand total of eight screws removed and replaced, pretty simple. I'd recommend buying two or three parts if you see several parts as possibilities for a repair. Easier than doing it the dummy way like I did!