1106007713 Kenmore Dryer - Instructions

Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.

The door catch kit is soo easy. They give you instructions on which one to use depending on your dryer and it fit perfectly into the door. This was great especially since it was so inexpensive! My husband thought we would have to replace the door.

Simply installed the piece and I was done. Took 10 seconds.

My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business again with partselect. Com if we ever need more parts.

Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your service. You made my life easier.

Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.

All I had to do was get the model number off of the dryer and plug that information in online and within a couple of days the part arrived. It was great! There were directions that came with the part that explained how to replace the old latch with the new one.

I remember in the "olden days" when I would of had to call a repair guy out and paid a lot more than the $12.00 I did to replace the part myself. And, the only reason it was $12.00 dollars instead of $5-6 was because I had it shipped overnight.

Awesome!

Popped out the old door catch kit and replaced it with the new one! Easy!!

Followed video on PartsSelect website, they made it real easy.

Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.

Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.

our son was able to diagnosis and order the part and very pleased with quite response. Dryer now working fine.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at

It was so easy! I simply fit the gasket into the groove where the old one had been. Didn't even need any tools.