11060022011 Kenmore Dryer - Instructions

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

Replaced Broken Belt and roller

I ordered the maintenance kit because it was recomended for my application and the symptoms my dryer was exhibiting. However this kit did not apply to my model. My model contained 4 drum rollers, only 2 came with the kit, and the idler pulley setup was completely different. I should have pulled the dryer apart first to compare pictures to the actual parts. No big deal, prompt refund after a quick phone call to Parts select. I was able to fix my idler pulley with a couple of new nylon washers and a new snap ring to hold it in place. Whirlpool cabrio wed6200sw1.

Followed instructions that came with part.

I tore down the dryer, to find any and all issues. The belt was worn, the rear support wheels were worn, the Blower Wheel was cracked and busted, the left felt support was absent, the right felt support was shot, the water tube leading to the steaming chamber was split in two and disconnected. Ordered all parts from here, they shipped VERY fast, and the hardest part is getting the drum back in and set right. The belt was fairly 3easy to put back on if you removed the water tube support and get your right hand all the way back in there so you can pull the pulley wheel back while holding the belt. Completely cleaned the cabinet out, vacuum and scraper. Put a new exhaust hose on while I was at it, just in case. Once everything was put back together, carefully, the dryer works as good as new. I was told to never get rid of this dryer, they quit making them, and I see why. Easy to repair, does my dress clothes in the top cabinet, dries like a commercial machine in the lower. Oh some installation notes...The front panel comes completely off, if you disconnect the ground and the yellow wire on the lower right (your right) side. This makes everything else much easier. There are 4 front panel screws, 4 edge screws, and four counter screws inside the upper cabinet that must be removed. I had to pull the side holder screws to removed the top plat so I could remove the drum. Keep track of your screws!!! You will need a flathead, a Phillips, a small socket (I forget what size), and some needle nose pliers to remove clips (from the wheel).

Removed top of dryer and front panel per instructions and removed belt and drum. After removing what was left of the old rear drum seal I scraped off and sanded the old adhesive off. Reapplied new adhesive and installed new seal after about 3 to 5 minutes (let adhesive get tacky) I then used about a dozen spring clothes pins to hold seal in place while adhesive set up. Reinstalled drum,belt,front panel and top and job was complete. Time included letting adhesive set up. Easy and inexpensive, thank you parts select.

Followed the directions on the web site. made a hook out of a wire hanger to hold the drum in place (hook from the back frame to the front of the drum) while I set the belt tensioner in place. removed the hook and the rest was easy.Works Great!!! like a new machine.

The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

Found right parts for problem on this website. Handyman took down machine and installed the drum support wheels. Taking apart was not too difficult; getting drum and dryer face aligned properly was a bit difficult and took longer than expected (and 3 of us). However, it was much better than having to buy a new dryer, since there was very little really wrong with this one. BTW, it was "out of warranty" so it would have cost around $150-$250 to repair using the repair service from the retailer we bought it from. Saved lots of money. Thanks.

I followed instuctions, also watched a how to vidio, had a little problem reinstallig front cover. The job took a little over a hour. The squeel was coming from old style belt tensioner.

Repair was as straightforward and simple as the videos implied. The most difficult part of the repair was disconnecting the door wiring. It could be more plainly shown in the videos. After that it was simple. The cleanup inside the dryer, lint, etc., took as long as the repairs. An extra set of hands to hold the drum in place while routing the new belt over the drive pulley would have made it even simpler. Runs like a new dryer now.

Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

Ok, there was a couple of other parts not on the video but were not hard to deal with. I would suggest talking a photo of the assembled parts before taking parts of for a reference when reassembling.

Viewed online video and written instructions that were included in maintenance kit.

Diagnose the problem. Is it the motor ? Is it the belt ? Order the correct repair kit, use name brand parts to ensure reliability. READ THE SUPPLIED DIRECTIONS. You can use a small wood shim or wedge at the top front corners to open the top . Use a 5/16" socket to remove the 2 screws at the top outside corners. Lift the front panel straight up, supporting the drum as you lift it off. Remove the drum, taking it straight out the front. Install the new drum rollers, install the idler, and then the belt around the drum. Install the drum on the rear rollers, make sure the seal is not folded under. Push the drum back against the seal flange, support the front of the drum with your right (or left ) hand, and sit the front panel on the lower pins, and gently push the front panel to the sidewalls. Feed the belt through the idler and around the motor pulley. This job is easily performed in about 20 minutes. Clean the interior while replacing the belt/idler and drum rollers. With the top lifted, after assembly, test run the dryer to make sure there are no "funny noises" after the repair. Watch especially for the white rub strips on the front edge of the drum. They tend to fold over when attaching the front panel. Job done !