1069808715 Kenmore Refrigerator - Instructions

I removed the self brackets and installed new parts, installed the enclosed tape on the bracket and reinstalled into the door.

unscrewed the old one! installed the new one! That simple. And I'm female, how easy was that!

I followed the instructions sent with the piece and VOILA it was repaired in less than 5 minutes. The whole process from finding the part of the web site to the ordering to the arrival of the part to the repair was so wonderfully simple. THANK YOU!!!

This was a very simple repair once I had the right part. And the thing that made ordering from you so easy was that you had all the diagrams online! This not only made the repair easier once the part arrived, but it helped me to be sure I was ordering the correct part in the first place. Now I know where to go for any appliance part I made need in the future. Thanks for helping me get it right the first time.

Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the harness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!

Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.

I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.

We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH

First I entered my model #, then picked the symptom, then went with the odds when presented with the likely suspects. The run capacitor, and bi-metal defrost timer had the highest % of guilt. Most of the time was spent defrosting the coils with a hair dryer. The run capacitor took 3 minutes to remove and replace. I snipped out the old defrost timer and used butt connectors to wire up the new one. The old timer flunked the continuity test when placed in salted ice water. The freezer/fridge runs like new, for about $66. The run capacitor was probably ok but I left the new one in, being too lazy to send it back. "Part Select" was a great partner in helping to fix my machine.

After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.

followed the video instruction from part select web site

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...

1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. Replace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.

We followed de video that made it very clear to us. Thank you! It's been working great since...