1069731611 Kenmore Refrigerator - Instructions

The best part was that it took 2 minutes to order the part on the internet, and the part was delivered in three days. Earlier than expected. it was packaged very well amd I was able to transport it to the refrigerator in our vacation home with out hiring a repairman or additional delay.Thanks.

1 removed bottom off old ice maker (3 hex screws) and ice drop shield (white plastic ice flips over into ice holder, old unit had different drop angle, see how described below, but I just musled it off the old unit) 2 removed "ice sensing bar off new ice maker and rotated mechanical sensor to on (leatherman tiny flat head) 3 removed end cap from new ice maker, then loosened to large screws (Phillips, leatherman) for motor unit cover. This allowed removal of ice drop shield on new unit (two tabs, one at each end). 4 removed ice drop shield and installed old ice dropshield on new unit 5 tightened two endcap screws (Phillips/leatherman) and reinstalled end cap 6 installed old bottom unit/tray on new ice maker (3 screws) 7 ensured wiring matched and routed plug properly 8 installed unit slides in 9 plugged unit to existing plug 10 installed old wiring shield (1 hex screw). Waited two hours to verify water valve worked properly, although IR codes did indicate "okay". Machine has been making ice and IR sensor shuts it off properly. So far a success. I have many spare parts if I need to do further repairs including a new water solenoid. Only saying it was a bit difficult because of the parts exchange, in actuality for me it was really easy.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.

Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!

Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.

I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim