1069354201 Kenmore Refrigerator - Instructions

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.

Removed the one screw holding the unit in place in the freezer and pulled it out. Removed the 3 screws that hold the motor in place on the ice maker. Replaced the motor unit, replaced the 3 screws, and re-installed the ice maker.
Sears wanted $170 for labor for the 10 minute job, plus $130 for the part, which I got here for $65.

The rental house I live in did not come with the original shelves for the Refrigerator. Had to strategically stack stuff on top of one another with locker shelves. Entered the model number on the site, order the best matching item, and the part that came was a perfect fit. I'll be getting another.

The repair was simple.

I first did a diagnosis of the optical cuircuits and found them good. The tray heated up and when resetting the moor controller, the water cyccled to fill the tray so the only other thing it could be was the motor controller.

removed the service door for the ice maker
I removed the wire protectore screw and shroud
pulled the icemaker unit out and unplugged the unit
removed the motor controller end cap
unscrewed 3 screws holding the motor controller
removed and replaced the motor controller. ensured that all wire harness connector poiints were solid
reverse the above instructions and in 5 hours I was getting ice again!

$90 turned out to be a savings from the $250 it would have cost to have someone come out and look at the fridge.

I highly recommend to anyone who can read and use a screwdriver to perform this repair if you have diagnosed this as the root of your problem!

Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.

I followed the directions and it worked.

I watched the video that was included with my on line order, it was helpful, although different model shown . I would say it was not difficult to install, the enclosed instructions were a bit confusing.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric

I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim

Followed the video instructions.