10684402 Kenmore Ice Maker - Instructions

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

Turn off water, removed two mounting screws, unplugged solenoid, removed incoming water connection and plastic pipe to ice maker. Installed new valve, connected water lines, reconnected plug, remounted with screws. Turned water back on, over rode power to ice maker and checked for leaks. Total time about 5 minutes. Very easy repair.

I ordered the part and just 1 1/2 days later, it arrived! Awesome!

I took the cover off the ice maker motor. Then I simply unscrewed the three screws holding the motor in place (be VERY careful - the hinge mechanism that holds the ice maker on/off bar needs to be gently removed from the motor so the prongs do not break).

Once the motor and ice maker hinge were removed, I simply pushed the new motor on, screwed all three screws back in, put the cover back over the motor, pushed the bar to 'on' and water flowed and ice was made! I turned it to Max so I would have lots of ice in a short amount of time then returned the switch to Normal and I've not had a problem since.

My husband is a plumber...but did not have time to make the repair. So I took it upon myself!

Super Easy!

1. Unplugged Fridge
2. Unscrewed the 3 screws on motor
3. Pulled out old motor
3. Had to pour some hot water to melt ice cubes that were currently in the shoot. (because the new part would not line up correctly because of the frozen cubes inside the maker). Then soaked up all the water with towels.
4. Inserted the new motor
5. Put 3 screws back in.

ICE, ICE BABY! Within a couple hours it was dropping ice into the bucket! Husband came home, and I told him I fixed the ice maker (his expression was of dread)...and then he checked it out and all was perfect! So proud!

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

Change motor on icemaker by taking the screw out the bottom ice tray so it will slide out once I remove the I took door off the icemaker it pops off. And follow the instructons for shower

3 Years ago our icemaker stopped working and we paid a professional $225.00 to come and repair. This time I chose to investigate the problem on line and PartSelect website gave me info on the motor assembly that may be the problem. Sure enough I purchased the part, it was delivered in two days. My husband installed the control & motor assembly in less than 15 minutes. We had ice within hours. Thanks for saving us a service call and the expense. The Goldbergs

I determined that the plastic lever inside the icemaker was broken and I found the part easaly. It was farelly inexpensive considering the important job the ice maker does, so I order it and paid for the standard, 5-8 days delivery. To my surprise, it was delivered (to my neighbors house thanks to the delivery person) the next day. Once Berry the neighbor delivered it to my house, 15 minutes later ice was being made. I had to remove one screw and losen two on top of the icemaker, disconnect power and remove the icemaker. I don't think that this step was even required but I wanted to remove all of the old ice from the maker without thawing out the freezer. Replacing the part itself also required removal of three screws. I think that almost anyone can do this easily (with or without Berry).

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

Went very easy, watched the video from the web site and did what it showed to do and put it together and it worked.We now have ice.

The first issue was to determine if the problem was with the ice maker or the water dispenser / pump. I chose to try to repair the dispenser first since there air bubbles in the plastic line. Also, the ice maker seems to have been working. There just wasn't enough water so the ice cubes were hollow.

I unplugged the power cord, , removed the cardboard backing and two bolts that secured the pump to the refrigerator. I vacumned the area so I could see around. I pulled the valve out and disconnected it from the internal power source. I disconnected the copper water intake and the plastic tubbing to the ice maker. I used a pipe cutter to take the old flanged area off. A new flange was included in the package. I used that and reconnected the copper intake and the plastic tubbing. I replaced the power source and secured the valve to the refrigerator makeing sure the plastic tubbing wasn't twisted. When I plugged the refrigator back up, the ice maker started working within five minutes.

replaced icemaker motor.easy peasy

Very simple repair. Ice maker was operating, but not receiving water. Once new valve was in place it works like new.

Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may take a period of time before it starts producing ice after re-installation.

I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.

The module cover is removed, then the module itself is easily removed by removing three screws.
The assembly is just as easy.

A few hours later, I had a half bucket of ice!