1068241540 Kenmore Freezer - Instructions

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

I tilted the unit back enough to scew the new legs into the threaded holes.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and replacing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!

Remove top henge, lift door off bottom henge, take off old plastic closer put on new one. Door works great now

Brought the inside of the door in tbe house were it was warm. Put gasket on keep inside over night. Screwed frame back on but won't close tigbt so used bungecords to pull tight. Plugged in frezzer left over night next morn took off cord and it sealed great.

removed screw on top cover emptied ref door remove 3 top screws holding bracket on top. lifted the door then remove old cam then reassembled.

I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.

Replaced very easy.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Removed all the adjustable shelves inside the door. Removed the top hinge cover (1 nut). then the top hinge bracket (3 nuts). The door doesn't weight very much so you shouldn't have to worry about the door just falling off after you remove the top hinge. then simply lift the door off the bottom hinge and carefully lay it down. One nut in each of the plastc cams on the bottom of the door and an easy swap out with the new parts. A little vaseline one at least one of the surfaces of the cam, reverse the order and simply put things back together and your good to go. Door closes on its own like new. You might as well get both parts for the lower cam and swap them out simultaniously since you have the door off. PLEAS NOTE: Yes there are two different parts for this repair.