10650045713 Kenmore Refrigerator - Instructions

I removed the ice bucket and dumped the ice (saving part of it to put back into the bucket after repair).Using the nut driver,removed all screws,rmoved the auger that the broken drum is mounted on.I reoved the nut on the end of the auger(with my pliers).Slid out auger removed broken drum,replaced new drum and re assembled using your easy to follow instructinns.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

It was a breeze to remove and replace. Made even easier by the previous DIY guys posts. Make sure you turn the nut at the end of the shaft clockwise to loosen. Taking a picture of the blades for ice crushing before removal for future reference is a great idea. It wasn't hard at all. Just take your time.

We took the icemaker apart, and took pictures of how it looked before so we knew how to put it back together, we were really surprised how easy it was to put back together, I will be ordering other parts from this company, I got my part in 1-2 days by Fedex, I will be telling others about this company

First I removed the 6 screws and then 2 more--being carefull to take cap off inside to nremove metal blades--be sure to keep in order--taking ba digital picture helps at this point--make sure to put back nin reverse order after replacing washer and new auger--went smooth thanks appliance parts repair service forum--Rick--Enjoy your own repair!!!

Pulled out the ice tray, took whatever screws held the front on. The rest was pretty easy. The only thing I would say was a problem was taking off the cutters. The front spacer is threaded, and loosens by turning clockwise. Also, the shaft that runs along the side of the tray has a spring and keeper. Make sure yoiu remember how you take it apart.

removed 9 screws, removed all parts, laying them in order, so they would be easy to replace.
reassembled in order I had removed them placing the new auger drum in place of broken one.
replaced ice container in freezer, poured in a few ice cubes them crushed them.

looked at the schematics from online

Had to replace the auger drum. Went fairly smooth. The video that was linked next the part was a big help, especially when all the blades of the ice chopper came off of the shaft at once and I needed to get them back in the correct order. I did a freeze frame on the moment in the video to figure out the order.

I began by removing the ice maker and storing the ice. The part did not come with instructions so I began taking the ice maker apart. I ran into problems rather quickly so I went to the "part select" web site and there was a video with instructions on removal and reinstallation of the auger. It was a breeze after that. These guys are obviously professionals!

This was not a hard repair. Just remove all the screws and slide out the old Auger drum. It is always good to take a picture first incase you have any problems putting it back together. Be careful to put the ice crushers back in the same order and make sure you look at how the "door spring" connects before pulling it apart.

Repair was easy enough, take apart and put it back in reverse.

removed ice bin from freezer then removed front from ice bin then all i had to do was remove e clamp from end of shaft that made it possible for me to remove the ice crusher parts then slide off the drum. all that was left was to put back together.

removed six screws removing the cover and exposing the shaft & auger.

I then had to remove the snap ring & undid the end nut that has left handed threads.removed the 6 auger plates and then replaced all parts in reverse order of their removal.