10642 - Instructions

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left no questions.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Pulled the refrigerator out from the wall, I had unplugged it prior so it didn’t burn out the compressor. Put both new pieces together, I ordered both just in case they were both bad. Used the screwdriver and removed the screws from the bottom cover. Removed the silver wire thing, unplugged the wire connector and pulled out the old piece. Plugged the wire connector into the new piece and pushed the new piece into the silver prongs, replaced the silver wire thing, put the back on the refrigerator and replaced the screws and crossed my fingers.
Plugged it in, turned on the refrigerator and freezer on from inside the refrigerator and joila it started right up and is working. I am a 63 year old female, and had watched the video first on how to remove and replace it.

I have a Whirlpool side by side refrigerator/freezer, 12 years old. One day it just stopped cooling and there was water running under the fridge (melted the ice in the ice bucket). Checked the freezer fan and it was working. I also checked the condenser fan by checking air flow under the fridge; there was airflow, so it was working. Listened to the sound of refrigerator. Noticed the compressor was coming on and after a few seconds clicked (tripped). I figured either the compressor is burned or the Start Device is bad. Turned the plug off, took off the lower back cover using a nut driver. Removed the clip holding the Start Device and gently unplugged the Start Device from the compressor. Measured the resistance across compressor terminals. They should all read some resistance (10,6,4 ohm roughly). Also checked the continuity between each terminal and compressor shell. They were all open (means no shorting). I figured the Start Device should be bad. Ordered new part for $40, replaced it with old one, put the cover back on. Plugged the unit on and everything was working. Remember that it takes a while to cool both compartment, so do not expect the fridge/freezer to get cool quickly.

Simple remove the fan and motor, plug in the new cord and screw in the new motor.

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio

pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that

I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

Very easy to order from parts select. Took seconds to replace.

It was very easy. The part make look different online but it was a proper replacement.

rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one